Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi! We're working on a BLE product which is intended for use in the US. This product uses an nRF52833 SOC, with some external components on a PCB we've designed with a printed...
I'm trying to evaluate a Nordic BLE module for a new battery powered project while waiting to establish a connection to a base station device. It seems like your lowest powered...
Hello,
When we tried to increase the Security level from SEC_OPEN to SEC_SIGNED_MITM, it will output error 0x6 which is "Not supported". So how can I do to support a higher...
We are developing AoA direction finding with nrf52833 and antenna array. We also want to include Wifi connectivity to our receiver, having nrf52833 + antenna array. Which...
Hello,
I want to perform NRF52840 Firmware update remotely. I refer to link .
I want only normal http OTA update without encryption for prototype testing. Is there any...
Hi, I've been measuring a nRF52840-powered prototype powered from a 3V coin cell battery. I would like to use High Voltage Mode with REG0 in DC/DC-mode for maximum battery...
Hi,
I am trying to implement the attribute reporting for a zigbee dimmable light device, reporting to the coordinator.
The code is based on the zigbee\light_control example...
MCU: nrf5340 Network Core nRF Connect SDK Version: 1.5.1 Currently there are multiple libraries under ncs/nrfxlib that have their own " nrf_errno.h" . Out of those libraries...
Hello,
i have a function wich just send "hello world" via uart0. static otError SendUARTCommand(void) { volatile uint32_t ret; const uint8_t message[] = "Hello World! \n...
Hi !
This is more of a question than an issue. I am curious about the future of TF-M and its implementation on Zephyr. Does anyone know what are the plans on Zephy's or...
I'm trying to set tx power to +3db in the peripheral_uart sample.
I don't need dynamic control, just setting to always use +3db.
Adding the following line to prj.conf...
Hi,
I am using coded BLE to connect two board using nrf52840. I just let bluetooth to run, then measure power consumption of the peripheral board by measuring the current...
Hi,
I am trying to send messages from my gateway, which has UART and __LOG enabled, to a specific LPN address (0003).
So I want to send messages from my FN Light1 (0002...
We have developed an application in ncs-1.3.0 where we created a west.yml file for the application that lists nrf, zephyr and other dependent repositories. We have downstream...
Hello. everybody.
I'm new to be here.
Now, I'm struggling to succeed in building 'ble_app_beacon_pca10040_s132.uvprojx'.
(This file located in C:\(private dir)\nRF5_SDK_12...
