Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi we are integrating a ANNA-B112 device from u-blox that use the nRF52832 core. The pin mapping for UART appears to be different for the Software (not open source) that they...
I have a general question that I haven't been able to clearly locate in documentation. How does the processor handle "traffic" jams from within the different app timers? ...
Hi everyone, so I have been trying to enable the nRF52840 to send notifications to the Nordic Connect app via a custom characteristic. The app can detect the custom service...
Hello,
I have an issue opening the power profiler kit 2 on my windows desktop:
Somethimes it works after restarting, but stops working after a few minutes.
After it...
With a baudrate of 1000000, when i transmit 2 subsequent packets (with ACK), i have to put a delay of 0.2 msec or more. Otherwise the second packet will get ACQ packet acknowledge...
We're trying to debug an issue with our nRF52 chip when pairing to some Android phones. On the nRF52 we are connecting to mobile devices by acting as a peripheral for the...
Dear friends,
I used a serial bootloader by this tutorial Secure DFU Bootloader over Serial Link (UART) , i can upgrade my application with the pc nrfutil tool, the nrfutil...
Hi sir,
I have a question for Bluetooth 5.1 single mode. As I know, above Bluetooth 4.0 has single mode and dual mode. Single mode only supports LE and dual mode supports...
Hi.
I'm newer on Zephyr.
I want to use the LOG Output.
LOG_DBG("main.c"); LOG_INF("main.c"); LOG_WRN("main.c"); LOG_ERR("main.c");
Everything works but the color of...
Hi everyone,
I'm developing a new application/product. It will feature a nRF52805 without the LFXTAL but with DC/DC support. I'm developing with the NRF5 17.0.2 SDK.
I...
Hello,
I am trying to commission a device running the CLI sample to an OTBR I configured following https://openthread.io/guides/border-router (the OpenThread official guide...
Hi
in Zephir nrf9160dk_nrf9160_common.dts the SPI pins are defined
&spi3 { compatible = "nordic,nrf-spim"; status = "okay"; sck-pin = <19>; mosi-pin = <18>; miso-pin ...
hello,
i am using nrf52832 with sensor which uses uart communication and using sdk 15.2 but i could not get my excepted values in rx buffer which is of 3 bytes and values...
