Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am attempting to change the passkey used in BLE Pairing/Bonding. In this case, I am using legacy pairing/bonding.
My idea is to have the central provide the passkey to...
Hi,
I'm new to C language.
In my main.c
In my Battery.c
My Question
The IDE will give a warning: No such file or directory. How to solve this issue, please?...
hi support team,
customer are asking one question about using external 32 MHz crystal, if customer not using radio, only take 832 as MCU, is it possible to using 26 M crystal...
Hello!
I just started with NRF Connect sdk but I have some problems. The nrf5 sdk was working fine for me but we decided to migrate in this early stage of development to...
Hi, it's my 1st time using nRF Connect SDK for nRF5340. After click OK (see screenshot), I had this CMake error.
Because my previous folder contains white space (C:/Users...
I've been trying to run the FreeRTOS blink example on a custom board.
After some time (I have not yet been able to determine exactly how long - but somewhere in the range...
Hello,
I would like to use k_uptime_get, however this is returning an int64_t where I would expect an uint64_t.
While looking in the function, I see that k_uptime_get...
Hello,
We need to add secure services to our application, and I followed the guide in https://devzone.nordicsemi.com/nordic/nrf-connect-sdk-guides/b/software/posts/using...
I have downloaded the ble_app_blinky_c_pca10056_s140 hex file to the development kit with the help of the nrf_connect windows application. I have a PCA10100 development kit...
There is no 32767Hz crystal oscillator on my circuit, so the clock source of softdevice is configured as RC to ensure that the system can function normally. Now I use the...
I have successfully run a firmware in NRF52840 DK board. With NRF52840 DK ,I have tested AWS IOT BLE Nrf. Now I have also NRF52840 Dongle. Because small form factor, I would...
Hi Nordic support,
I was trying to get the Asset Tracker app running on the Thingy91 device but encountered various problems. Basically it can't get connected with the network...
Hi,everybody!
I started to connect the PCA9685 to the nRF52 DK and ran into a strange problem. When initializing the PWM module, it does not work.Initialization requires...
Hello DevZone,
I am developing on nRF5340-DK v0.11.0, with nrfx v2.2.0 running with mbed Cordio, compiled with GNU make 4.3. The end goal is to make a Bootloader for the...
Hello everybody. I need to rotate servo and check adc on potentiometer to stop it if something is blocking the shaft.
I need to change servo position step by step and check...
