Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
As I know, nRF52 series is produced in the TSMC on 55 nm ULP process. But I can't find any info about the integrated circuit manufacturing process of nRF53 series. Could you...
Hi, I use a nRF52840 with the nRF Sniffer Firmware for capturing advertisement frames and connections between several devices. My question is if it’s possible to capture communication...
I'm writing custom boot loaders. One of the capabilities is to update the network processor from code running on the application processor. The PCD subsystem looks like it...
On 3/11, we received a message from the Nordic "HomeKit Team", announcing that HomeKit support in now integrated in the latest release (ncs 1.5.0) and distributed through...
chip - nrf52840 sdk - nRF5_SDK_15.3.0_59ac345 softdevice - s140nrf52611
Issue enabling usb cdc without softdevice enable.
The COM port does not show up without the softdevice...
Ring buffer operates on uint8_t , but I would like to use ring buffer to store 16 bits ADC data. What is the simplest solution?
Converting 16 bits data into 8 bits, store...
Hello, Guys!
As I know, the Bootloader uses RTC2.
The problem is that RTC2 continues to operate after executing the bootloader, in my Application.
My Application not...
We are using nRF52840-DK and we need to stream the audio to our iOS app that we are developing. But currently, we are not able to get the audio streams back for mic to iOS...
In my application we have an ADC input pin which we want to connect to comparator input too. Based on the highlighted statement in section 7.6.1 Can the same analog pin be...
Hello,
since a few weeks I have the following problem with the nRF Connect for Desktop app on Linux (Arch Linux specifically). The runner launches and I can install and...
Hi,
starting the NCS v1.5.0 "Bluetooth: EnOcean" sample on nRF52840 DK, the following error occurs:
Bluetooth init failed (err -35)
Any suggestions? Thank you.
Hello
I'm testing multiple frequencies to ensure smooth ultrasound control.
Frequency can be generated via 'APP_PWM_DEFAULT_CONFIG_1CH (period, pin)'. But it seems difficult...
Hello there
I hope you are doing well
I am looking for rf module that meet my requirements, please check these requirements below and give me any of your product meet...
Hi Nordic,
I am using one NRF52840 named A chip(DCDC mode) to provide VDD power supply to another NRF52840 named B.
A is using VDDH with battery 4.2V power supply.
B...
Hi,
I am using nrf5340 kit. I would like to enable and test power management in mesh chat example.
1. Can you please tell me the usage of below config file usage.
#define...
