Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hi,
While going through some of the peripheral examples in 'nRF5_SDK_17.0.2', I found it puzzling to see that
the legacy (nrf_drv_*) and nrfx_* drivers are simultaneously...
Hi all,
trying to get CAN-bus support under Zephyr. Have a seed CAN bus shield link connected to PCA10040. The shield use SPI2 connected to MCP2515 CAN controller link ...
Hello
Is it possible to use the qspi of the nrf5340 for custom spi devices? I need the quad spi for the 96MHz speed which the normal spi does not have.
I know of the nrfx...
Hi there,
I am using the Nordic SDK 16.0.0 on an nRF52840 with FreeRTOS. I am quite familiar with using FreeRTOS, but hadn't needed to delete a task until recently. It seems...
Hi everyone,
How could I disable notifications from a characteristic when the peer is get disconnected from the the peripheral? My problem is that when notification are...
Hi,
I was investigating the registers of the nrf9160 using segger embedded studio and found POFCON, which is not mentioned in the documentation.
Can you provide...
I need to add some IPSO objects for our project. It is not quite obvious to me if I need to create modules similar to i e ipso_temp_sensor.c or if it would be enough to use...
Hello, guys!
We are desiging our custom board based on nRF9160 SiP. The board will be battery powered. Li-Ion rechargeable batteries will be used to supply the device. ...
Hi to all,
i am developing a device based NRF52840 soc, and i want to implement a device that need to store some public/private key in somewhere. i know that cryptocell...
Hello,
I am developing on the NCS 1.4.0 and on a NRF9160DK. I am working on the asset_tracker example and I noticed that the code sends an assisted gps request to NRF...
Hi,
I am using app_uart library with Tx and Rx FiFo. I want to check how much space is available in the Tx FiFo at any time, and similarly how much space is filled in the...
Now I am using Nrf52832,SDK15.0.0, S132,
When we developed the DFU OTA function APP, we encountered some abnormal situations: it could not get out in the bootloader mode...
HI,
I am trying to read the payload length of the data coming in a topic via MQTTSN over OpenThread. In the event handler, I am getting the event and trying to get the length...
Hello everyone
I am having a problem with the nRF Connect SDK 1.3.2 and the bluetooth peripheral UART sample on the nRF5340 PDK. The programm compiles and runs (the chip...
