Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
KeyWords: nRF52832 ESB Flash as EEPROM SDK:17.0.0
Hello, I an using nRF52832 developing ESB communicution with other nordic product.
I need to save some infomation, so...
Hi,
I got today a sample of your Nordic Thingy 91 device. I like to integrate the device into our IoT Data Provisioning Service from IoT Creators (Deutsche Telekom IoT...
Hi Everyone
I am able to write and read to and from QSPI memory interfaced with nrf52840 PDK.
I am using Segger Embedded Studio with sdk15.0.
I want to create a text...
If I write a value to ERASEPROTECT.DISABLE -- which itself works, as I'm fully able to perform the mass erase by writing the same value using the debugger -- I can't seem...
Hi,
We are using NRF52833 as a BLE central in our latest product and is undergoing radio certification tests. We are using SDK16 Radio Test example for the tests.
...
Hi,
We recently came across this network stack vulnerability called ripple20 and would like to know if there is any possibility of the same being present in the network...
Hi,
If i use nrf53 to interface with a modem(nrf91 or any other modem), is it possible to run the the TCP + TLS stack on nrf53?
In case nrf91 the the BSD lib runs on the...
Hello,
I am currently developing an Android library to connect a smartphone with a peripheral device that serves several bluetooth services. BAS, DIS and 2 other private...
Hi I have fired up nrf5340 pdk and downloaded the sample HRS hex images and I can connect using my phone app.
Is there a detailed step by step guide similar to the one available...
Hello,
I have a production device (NRF52840) running a version of the Legacy bootloader from SDK 11.0 and I need to update this to the latest secure bootloader.
Old Device...
Hello
I would like to add Power Management to the BSP example and I'm doing as follows (using SES 5.10):
add #include "nrf_pwr_mgmt.h" and nrf_pwr_mgmt_init(); to...
I have ~600 bytes of configuration data total that needs to be saved each after a sensor joins the Zigbee network, details like:
IEEE addr
end point
Join state details...
I plan to use nRF52832 BLE chip of your company. Now I have the following questions: If I use internal 64M RC, can I use Bluetooth function?Is the 2.4g transceiver accurate...
Hi,
I am have programmed my Thingy 91 device with lte_ble_gateway program to collect data from 5 Bluetooth devices and send them to the cloud. This program runs fine, however...
