We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Hello,
I'm struggling understanding how DFU works on nRF52840.
I know I can update the firmware via the Connector application, but I'm trying to use the nrfutil over command...
Hi all,
I am using Thread SDK3.1 and running successfull with MQTT-SN example (Border Router + 1 MQTT public + 1 MQTT subscribe)
Now, I want to change MQTT broker from...
Hi,
I am programming for an nRF52840 chip. I am using Keil uVision with the ARM compiler in version 5. My codebase is in C++, this is why I have the Misc control "--cpp...
Hi
I am currently using a nRF52833 DK. I am working with the direction finding feature of the nRF52833 DK. I have managed to send and receive CTE packets and I am getting...
The link given still points to the windows executable when selecting macOS or Linux on https://www.nordicsemi.com/Software-and-tools/Development-Tools/nRF-Connect-for-desktop...
I have CONFIG_GPIO_AS_PINRESET defined in my project (both bootloader DFU and main program), so pin 21 is setup as hardware reset.
I would like to disable this function...
Is it possible to use one of the development kits to simulate a cell phone so that I can test my device's bluetooth pairing, connecting, and communication?
I know I can...
hello, I'm working on the nrf52832 and sdk15.0.0 , I made my first custom perihperal with custom services, and now i want the device to be connected only to the first device...
I just got my developer Kit and follow the instructions in https://www.nordicsemi.com/Software-and-tools/Development-Kits/nRF9160-DK/GetStarted#infotabs -> GET STARTED
when...
1. Is there any document available from Nordic that describes the exact steps to measure power consumption in PSM mode with the Dev Kit? Also, is there a test firmware available...
Hello,
When in try to activate "Console 'get' function selection" in menuconfig, I get an error "ERROR: undefined not in named choices or syms".
Can someone help me please...
Hi all,
I am doing a project with nrf52840 tags. I would like to collect the RSS values and the time stamp with my Android phone. I can see in the nrfConnect application...
Is the data stored in internal flash for mesh encrypted?
Or is any of it encrypted?
I'm talking about the data explained in this link:
https://raw.githubusercontent...
Hi,
I have test setup consisting of 2 boards, one that sends a packet every 2 seconds with CTE, and another with a 2-antenna array that generates MagPhase samples and sends...
Hi,
I am using "http_upgrade_ota" project.
I have added UARTE2 , SPIM3 and WDT peripherals in the application.
To use this peripherals i had to make change in "spm...
