Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi,
I have read through this tutorials on how to develop custom UUID, and I have implemented it successfully.
But I need to have 2 characteristics. I have basically duplicated...
Hello. I am trying to use TWI with mpu9250 sensor after System Off mode. But it is not working well. Do I need to do some preparation before going to System off mode? Where...
Hi All,
I'm using Ellysis sniffer for debugging my ble mesh network.
I've made network setup using generic on/off application and I'm able to communicate and capture...
I have a nRF9160 DK and since I am in Germany, we are trying to use the most common LTE band they use here, which are:
Band 1,3,7,20
However, band 7 does not seem available...
When I compile one of the nfr_log modules (e.x. nrf_log_frontend.c) I get the following error.
I do include ../components/softdevice/s132/headers/nfr52 in my User Include...
I have an nRF9160 DK which came with an enclosed eSIM from iBasis, that is supposed to work in most of Europe.
However, after jumping through all the getting started hoops...
Hi All,
Posting this here after a lot of searching and troubleshooting. There have been a lot of similar posts but none actually seems to go into how to implement this in...
I'm successfully printing to the UART1 com port at baud rate 115200, but I have a peripheral I plan to connect that requires 9600. What is the proper way to go about this...
I'm using an NRF52840, SoftDevice s140, FreeRTOS, SDK 15.3.0.
I'm trying to sample my ADC at high speed, >1khz (10-40kHz).
I implemented the logic from the SAADC exaple...
Development environment：
NRF52832
SDK：15.3
SOFTDEVICE：NONE
When testing the FDS module power-off data protection feature, the FDS module is abnormal.
During the...
I have a PCB containing an nRF9160 using a SEGGER J-Link. I am able to update the application firmware at will using a variety of tools but if I use nRF Connect v3.2.0 to...
To the kind attention of Nordic support team,
I'm considering to get started manufacturing mini dongle nRF52840 based as in https://devzone.nordicsemi.com/f/nordic-q-a/48568...
I have the following problem:
I want to update my application code via BLE with the secure bootloader. This works perfectly while the J-Link-RTT-viewer is connected.
When...
Hello
I am using the basic asset tracker example + https://nrfcloud.com
I can see messages from the device to cloud, how can I send commands from cloud to device?
...
Like the question, I want the dongle to be detected as a bluetooth device but not a serial port. Is there any method to do this?
And I want to ask if it be possible to build...
