Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hi,
I want to test BLE 5.0 using two nRF52 dev kit. i am using the ble_app_uart example kindly guide me what are the changes to made in this example to connect two kits...
It's easy for me to create make file target but I am not able to identify where and how to add the custom target in the Segger Embedded Studio(SES).
My default build configuration...
Hi everyone. I am trying to find the best way to establish a Bluetooth connection to a nRF52832 in the least amount of time.
I'm designing an ultra low power perpheral...
Hello,
Would it be possible to create a partial code that can be placed on external memory, and loaded into ram for execution when needed?
As I believe it is possible...
Hi,
I am developing a Bluetooth peripheral application using NRF52832 MCU , where in it is used for collecting vibration sensor data for about specific duration.
like...
Hi,
firstly, I have to say, I use MBED OS, if you cannot help me because of this, I understand, but maybe somebody still has some general Ideas.
I am trying to build an...
Hello All,
I am new to Nordic and i have nRF52840 development kit. I want to build code/ programm on thread and Zigbee base.
I have downloaded the Thread and Zigbee SDK...
Hi!
I do not know what the problem is.
First of all, I use nrf52-dk and SDK 15.2
And then, i read 'PPK User Guide v2.3'
I use 'nRF Connect > Power Profiler' to measure...
Hi,
I use the SAADC with the NRF52832.
This is the schematic used :
When we use AN_IN (TOR_IN 1 and TOR_IN 2 are not used), only the components assigned to AN_IN are...
File nrf_pwr_mgmt.h is lacking
#ifdef __cplusplus extern "C" { #endif
magic.
SDK version: nRF5_SDK_15.3.0_59ac345.zip
I guess it is a small oversight since all other...
Hi using nrf52 SDK 15.1, on custom boards
I have certain flash operations using FDS. I have peer manager as well.
I am writing 8 byte data & later in the code updating...
I am attempting to develop an application for a custom board with the nRF52832. I am attempting to use the UART functions in the SDK but I am running into compile errors....
Hi, I am trying to fix a crash in the dfu service. I am using a custom board based on the NR52840, SDK 15.0 and softdevice 6.0.
I am trying to add some new characteristics...
