Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Above is my code. I am using Keil uVision5 IDE on Windows 10. I am flashing s132 and then application hex to device using nRFGo.
My goal is to take a square wave as input...
hi,
I am using nrf52832 board,sdk 15.0,soft device s132. i can upload both soft device and bootloader, after that how can i upload my application file .i want use both uart...
Hi all,
I am working on sending messages from nrf mesh app (proxy client) to proxy server ( nrf 52832 DK : running light switch example from nrf5 sdk for mesh v. 3.1.0)...
I am trying to program an external board nRF52810 using debug out on PCA10040. I was successfully able to program an external PCB board with nRF52832 using PCA10040,
but...
Hi folks, I'm receiving a special timestamp over bluetooth, and I want to write it to an external memory. I want the time at which it was written to the memory to be as precise...
I use Nodic sniffer nRF_Sniffer_200_beta3 to capture BLE Mesh packets, but found one strange scenario:
1 if set channel filter 37, 38, 39, can capture 3 packets in channel...
Hi,
going on with the migration from SDK 14.2 to SDK 15.3 it keeps on making trouble. Now the spi_mngr is not working anymore. After changing all calls to perform with extra...
We are using the SPIM driver to support a propriety 1-wire protocol used by a TI LED driver (TLC59731). To do this, we're using the MOSI pin exclusively and, for it to work...
I have been trying to get 125Kbit and 500Kbit coded phy wokring by directly using NRF_RADIO API (no softdevice in use). I have followd for example these instructions, but...
Dear all developers,
I'm currently studying about nRF52832 SoC and prepare to develop low current BLE device.
Before starting, I want to know about idle current consumption...
Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello,
I post a question last day, and I can not open it any more now, it always saying "Content is under review"
Even the question has been replied to:
The link:...
I don't use SoftDevice. If I initiate flash partial erase process, my understanding is that the system will do smaller portion of erase, suspend, erase again, until the whole...
I'm developing an application on an nRF52832 revAA that logs data coming from the app_uart module. It logs this data to an SD card using the fatfs library; the code is more...
I need to implement a uint64_t counter that increments every microseconds that I can then read.
I tried to use the timer API and increment the counter in the event handler...
