Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Hello,
Working on MAC. High Sierra.
got a 52840 dongle (but also a thingy and a devkit following the latest conference)
Trying to start at the beginning and build...
Hi,
currently I am trying to figure out how to disable the cryptocell hardware after enabling it, because if I enable it and then enter systemOFF, the system still draws...
Hello,
I am using NRF52840 Preview DK, I am running peripheral/SAADC example on the board, I shorted Channel 0 and GND on the board and I am receiving negative values...
Hello
I am using Android and BLE communication with nRF52832 (BLENano2) now.
I am using SDK 15.0.0 with keil uversion.
Central is Android and peripheral is nRF52832...
Hi
Using SD Version 6.1.1 and NRF Version 15.3.0.
Using the following advertising params I can set non-extended advertising
ble_gap_adv_params_t advertisingParameters;...
Hello Nordic support, For long term power profiling of nrf52 hardware, I am using the suggestion given here, that makes use of functions in python script ppk.py: https://devzone...
Hello Nordic Team,
I have an application in development where some bigger files (~20kb) can be downloaded into the device, so they get stored in with the FDS system.
Now...
Hi,
I am using BLE application in NRF52832 board and using NRFConnect app to send custom characteristic service from mobile app to nordic device. But if I am sending a data...
I updated Thingy:52 to firmware version 2.2.0 using the Thingy:52 Android app.
WIth the Thingy:52 running v2.2.0, the WebApp for Thingy:52 can pair with Thingy:52 but it...
Hello Sirs,
We implemented a joint bandwidth test (or speed test) for a radio channel by transmitting notifications.
Parameters set in SDK config:
#define NRF_SDH_BLE_GATT_MAX_MTU_SIZE...
I am following the instructions at infocenter.nordicsemi.com/.../nRF52840_PDK_User_Guide_v1.2.pdf to program a pre-compiled example (blinky).
I have two nRF52840-PDK (PC10056...
Hi, im designing a beacon based on nrf52832, but i have a question about RF section, i´m using 2450AT18B100E chip antenna, and to match it with the nrf52 i'm following the...
Hi,
Trying to investigate eddystone protocol. After compiling and uploading ble_app_eddystone example I see Eddystone BLE device in non-connectable mode.
But after pressing...
