Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi ,
We are using the BL652 module with your nRF52832 chipset in our important product.
In our product the wireless connection is fundamental and we would like to test...
Hi,
I am using nrf52832 to achieve system-off with low power consumption. Nrf52832 and a rf IC communicate via SPI.
I configured a pin as the wake pin.
nrf_gpio_cfg_sense_input...
Hi, I am trying to use github.com/.../nrf52-ble-image-transfer-demo with Ubuntu 16.04 Using - gcc-arm-none-eabi-6-2017-q2-update - nRF5 SDK version 15.0.0 (nRF5 SDK version...
I use SDK 15.3.0 with the example of USB_CDC. In the example, the virtual com port transmission works only when the terminal sends a DTR signal. I need the DTR notification...
Hi
I am trying to implement DFU to my project. I have done all the steps to generate packages, private and public keys etc. My program now starts at dfu and I can upload...
Hi,
setup: nrf52840 dk, no battery installed (power comes from USB connectors), switches are in default mode (SW9: VDD, SW6: default).
Flashed open_bootloader (dfu/open_bootloader...
Hello,
I'm using S112 V6.1.1 with the Nrf52810. I get a error using sd_ble_gap_adv_set_configure() after a connection. On BLE_GAP_EVT_DISCONNECTED i try to change the advertising...
After testing the nRF9160-DK with all available samples, we decided to integrate the nRF9160 in an own new product and have now a prototype available. And of course some questions...
Hi,
I am using Mac OS and 15.2.0 SDK on nRF52832. I was trying to do BLE DFU following this link . When I was trying to push the DFU zip file, It was resulting in the following...
In following the instructions of the nRF_Sniffer_User_Guide_v2.0.pdf, I'm attempting to use Segger's J-Link software to configure my nRF-51822. The environment is a Mac OSX...
I bought the nRF9160 dev kit and I can't connect to the j-link: JLinkExe SEGGER J-Link Commander V6.30f (Compiled Mar 2 2018 17:30:55) DLL version V6.30f, compiled Mar 2 2018...
Hi ,
In the target hardware I am able to detect the Nordic chipset nRF52480 by flashing USBD application on the chipset using JLINK SWD.
Now I have query related how I...
Hi!
With the nRF Mesh 1.2.0 on Android is only possible to set not group address as publishing address.
For group address happens nothing in the app and the device....
Dear,
I tried the same code on :
https://devzone.nordicsemi.com/f/nordic-q-a/43774/simple-gpio-example---nrf9160-dk/173275#173275
and my code:
The Led1,2,3,4...
I know how to set high power (8dBm) when running a nRF52840 as a peripheral (i.e. sd_ble_gap_tx_power_set(BLE_GAP_TX_POWER_ROLE_ADV, m_advertising.adv_handle, 8) ), but how...
