Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Does anyone know when will ANT SoftDevice be available for nRF5 SDK v15? Accordign to https://www.thisisant.com/developer/components/nrf52832#tab_protocol_stacks_tab, only...
Hi
I try to communicate with my NRF24L01+. For this, i have connected a mikrocontroller to my Module. Actually i am using a small piece of code, which allows me to send...
Hi,
In my project, I use button for put on the microcontroller in sleep mode. I implemented one timer that when I press more of 5 second the button, the micro call sleep_mode_enter...
Hi,
I have included in my code the code from the twi_scanner example as a starting point for using TWI in my board. When compiling, I get the following error:
../.....
hi,
Please Refer Light Switch Client Example in Mesh 2.0
I would like to know Code where and in which File the UUID from the unprovisioned Node is captured ?
Thank ...
Hello,
What is the switching frequency of the buck regulator integrated into the nRF51822?
The characteristics of this regulator do not seem to be explained in the documentation...
I'm following the Custom BLE Service Example , and using:
Segger Embedded Studio Release 3.34a
macOS 10.13.4 (aka High Sierra)
nRF52 DK (PCA10040, nRF52832)
nRF5_SDK_15...
Hi,
I am investigating an alternative to an implantable device that currently uses NFC.
The device range would only be about 3m and the data would only be transmitted...
this packet is capture by wireshark .I use nrf51822 and sdk12.3 connect Balance car,but the packet not have LL_VERSION_IND, LL_FEATRUE_REQ、and LL_Connect_UPDATA_REQ these...
Dear Nordic Team,
Thanks for supporting.
now i am workwith secure dfu. I followed this link https://devzone.nordicsemi.com/b/blog/posts/getting-started-with-nordics-secure...
hello
I am just starting to use the nrf52832 .
I design the PCB with nrf52832 and want to load the softdevice.The nrf go studio can not detect the nrf52832, but the keil...
I was facing some issues getting PWM peripheral work on my custom nRF52840 board. And then I tried the pwm output on P0.08 instead of P0.06 and the signal came out just fine...
We're developing a new device for a regulated market (medical). As such, we need to have control on what third-party software we're using, and how it is working. While starting...
I wanna implement this code for the app inventor, but there was several problem here. I can't use array or index for developing my trapezoidal method.. like this..
code...
