We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
Hello, I have an adafruit bluefruit feather m0 which has nRF51822 on it, I was able to establish a connection and send data until yesterday. When I try to find my adafruit...
Hi All,
I have a general question about the FreeRTOS implementation for SDK 14.0.0.
I've added FreeRTOS onto a basic UART BLE peripheral example that I wrote. I referenced...
Hey Guys,
I'm trying to import an existing Keil project into Segger Embedded, SDK 12.3.0.
I know this link exists which explains importing prior to SDK 14.2.0. However...
In the PS v1.4 pages 13-15 related to the QFN package.
Pins 11, 12 (P0.09, P0.10) are marked with the note '1'.
On page 15, at the bottom, the notes are enumerated:
...
I have a button that will put my device into pairing mode. While in this mode, I want central devices that connect to form bonds so that when not in pairing mode I have a...
Here I document how, in Eclipse, to start two, concurrent debugging sessions to two NRF5DK boards (or other debugging probes) , connected to different USB ports of the same...
Hello everybody,
I have problems with selectivity when I scan. There are 5 peripheral devices with different " DEVICE_NAME " but the same UUID and type (same " ble_uuid_t...
Hi, I am working on a custom board of NRF 51822 driving multiple leds from pin 21 to 30. I am trying to get and transmit the status of all the pins with help of bsp functions...
Hi,
We'd like to implement a feature that allows changing a BLE connection from [central device #1 -> peripheral] to [central device #2 -> same peripheral] (similar to Apple...
Dear friends,
The nRF Connect BLE app is connected with a local device acted as Master. The app supports the configuration of the local device's GATT attribute table, and...
Hello,
After i uploaded a program on my nRF52832 i couldn't enter debug or reprogram the chip. This is the error i get when trying to erase the chip using Segger J-Flash...
Hi,
I am using peer manager to use static passkey with nrf51822, sdk11 and s130 v2.
Is the "case PM_EVT_CONN_SEC_START:" the best place to put sd_ble_gap_tx_power_set...
I know this question has been asked before. As a beginner to Nordic, I tried to get the information here, but ended up even more confused.
I am trying to set up a Bluetooth...
