What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi
I have a question about using gazell link layer and paring library with concurrent timeslot api. I try to do this but i have the hard fault handler after invoked nrf_gzll_init...
HI,
I want to use PWM to control various hardware (LED's, etc ..) so I started off from the suggested PWM code example, found in this forum + modified it as I want to use...
Hi
I am using ATM90E36A IC from microchip for which Microchip gives ATMEL studio library.
Is it possible to compile the library in Nordic SDK 15 and use the functions...
Hi, Great Nordic support team:
Our client Is wondering if there's a way could sense the level of a GPIO configured output?
I mean, sensing the level without config the...
I am trying to do just bonding when I receive the BLE_GAP_EVT_SEC_PARAMS_REQUEST event as described in the sequence chart in this link infocenter.nordicsemi.com/index.jsp...
Hi
I have a problem with long latency on interrupts and long delay on retriggered interrupt.
I have a nRF52832 running with external HFCLK source. Using the SDK 14.2.0...
Hi, Im trying to add multiple endpoint support to a zigbee project.
Im using the SDK for Zigbee 2.0 but in the documentation says:
" APIs for multiple endpoints A single...
Hi,
If you are using NRF52840, I am using SDK14.2 and Softdevice 5.0.0-2 version.
I want to update to SDK15.1, Softdevice 6.0.0 via USB bootloader DFU. Is it possible...
Dear All,
1. I'd like to know if below two lines which high-lighted in RED , Line width should be designed to provide 50 Ω impedance matching characteristics ?
...
About the data rate item of 5.4 Receiver Opetation in the data sheet of nRF24L01 +. Sensitibity is -82 dBm at 2 Mbps and -94 dBm at 250 kbps, is 250 kbps more susceptible...
Hi all.
I have a working multi-link central NUS project, and a working USB_CDC project for the nRF52840 SDK 15, nordic dev board.
I have merged the two as I need a USB...
Hi
I have a RGB LED and want to have bellow process for brightness:
Red from o to 100 then Green from 0 to 100 and Blue from 0 to 100.
till now i by bellow code i can...
Good afternoon,
I am currently using ble_app_hrs_rscs_relay example in the ble_central_and_peripherals part of the SDK. I am just testing out the example and trying to pair...
i am using the nrf52840 ble-uart development kit examples ( ble_app_uart_pca10056_s140 ), with an nrf52840 development tool board. Connected to a device that only accepts...
Hi All,
Currently, I am developing on nRF52840 and use nRF mesh application (android app)for provisioning and configuration.
So, for the publish and subscribe address...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
I am responsible for developing auxiliary logic in the nrf51822 and have run aground on an issue which I have not been able to find a solution to on my own so I am going to...
