Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Using softdevice s132, nRF52832 on a custom board
I don't quite understand how does the SPI work exactly?
I am using it on a battery powered low power sensor application...
Hi,
We are unable to run testing with Nordic nRF52840 preview DK boaed as it is not able to be put into DTM for RF-PHY testing.
I need the hex file to flash and the...
In the nrf52 specification:
"The Phase A, Phase B, and LED signals are mapped to physical pins according to the configuration
specified in the PSEL.A, PSEL.B, and PSEL...
Hello Everyboby,
I want to know how to configure can use Public address for advertising when using nRF connect APP? Now, I just can use Random address for advertising...
Hi,
for production purposes, we need to define the components of our circuit. Less specific definitions of the parts are prefered to ensure the interchangeability of common...
Hello is it possible to send message from nrf52840 to nfr24L01, I tried (pca10056 as transmitter), program is esb_ptx_pca10056 and nrf24L01 as receiver, but could not receive...
Hi,
I would like to create a DFU package for updating an application config flash page.
We have a device where the device reads some configurations from a specific flash...
Hi Team,
Scenario-1:
There is a use-case where 8 to 10 peripheral devices need to be connected with the HUB which is based on nRF52810 and a mobile device should be...
I'm working with nRF52840 on a battery powered device , as a result theres a constraint in the total power of the cell . Now , it's been decided to use the USB2.0 at full...
Hello,
I have a problem with communicating with SD cards ( https://devzone.nordicsemi.com/f/nordic-q-a/34401/fatfs-example-does-not-work-with-every-sd-card ). I resloved...
Occasionally, the NRF_LOG output just keep putting out random old log data. I have enabled the timestamp so I know they are old data. Once it happens, it just stuck in an...
Where do we get support for NRF24L01+ ?
There is no option in the pull down menu for the device.
I attempted to set up a profile for private support but they have made...
Hello , I am having 3 nRF52832 DK . I tried Light switch - proxy_client and proxy_server example . I provisioned nodes using nRF Mesh app . Here i want to send data from server...
Hi! I'm trying to figure out the nrf_ringbuf module, and would really appreciate some advice about its intended use case. The api exposes the following functions:
This...
I created a DFU package from the HEX file through following command nrfutil pkg generate —hw-version 51 —sd-req 0x5A —application-version 4 —application /Users/username/Desktop...
