Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
I want to read whole flash memory using for loop and see how long it takes. What i have noticed is that it does not print all the lines. On the other side i ask myself: Does...
Hi,
I am very new to nRF51822 controller. i got some problem with compilation.
i have downloaded SDK v10.0xx and tried to compile blink example from following path.
...
Using Segger Embedded Studio 310i in Linux and SDK12.2.0, I imported the Beacon example project (ble_peripheral/ble_app_beacon) from Keil. Right now I'm trying to make it...
Hello everybody,
RTC0 is used by the SoftDevice. Is it possible to use the current RTC0 counter value as a system time, so that RTC1 doesn't have to run additionally? For...
I created a service with several characteristic values. I can read the values without any problem with the Master Control Panel on my Android tablet, but reading from the...
I am working with nrf51, SDK 11, S130, Keil uVision 5 and have an Application with RTX and want to use DFU OTA.
The bootloader works with the app_hrs_dfu example.
When...
Hi, I tried to enable non-connectable advertising timeout using the macro APP_CFG_NON_CONN_ADV_TIMEOUT in es_app_config.h, but it has no effect. I test this using nRF connect...
Hello,
When I call TASK_START in SPI Master it does not start a transfer. According to registers all seems to be set.
I found what was the problem. When I called TASKS_SUSPEND...
I am using SDk 11. S130 V2.0
What is the equivalent of spi_master_evt_handler_reg ?
I just want to configure my handler to receive the interrupt of the SPI master.
Please...
Hello, I've just purchased nRF52 dev kit and I'm using ble_app_uart example from SDK_12.2 to send/receive data from one pc (which is connected to the dev kit through usb)...
I have been trying to use nRF5 SDK 12 on nRF52 Preview DK by using PCA10040 instead of the removed PCA10036. But example 'ble_app_hrs' that uses SoftDevice S132 v3.0 do not...
Hello,
I am developing a custom board using nRF52. In my previous custom board, the total current consumption is 15mA with DCDC regulator enabled. I want to reduce this...
Hi,
I'm trespassing some code of nRF51 to nRF52 (s132, SDK 12.2.0) and I get an error when I try to call sd_ble_gatts_rw_authorize_reply. This is the code
case BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST...
I'm using the beacon example (SDK 12.2.0) which I've modified slightly so that a sensor output initiates advertising for 20 seconds with LED1 flashing accordingly. I want...
Hello I was working with the Flash Storage examples in the nordic github repo. I noticed that the FDS example while it has a IAR Workspace it does not have the associated...
