Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
I want to make a blinky program from scratch and have no idea how to settup keil. I would prefer something step-by-step. I have been able to use the precompiled example, but...
Hi all!!!
I'm new in here.
I'm reading document with link: developer.nordicsemi.com/.../index.html
In Figure 1, I see a phare: "IoT Device". Is the "IoT Device" nRF5x...
Hello,
my setup is nrf51822, with SDK 10.
I try to create application to drive I2C components and I get compilations errors:
In function 'Hal_I2cInit':
../../../nrf5...
I notice that Gazell could only send 32 bytes per Payload in nRf51 series. So i wanted to know what can be the maximum speed i can attain using that payload.
Hi,
I would like to test the maximum efficency build, with settings like this :
#define MIN_CONN_INTERVAL MSEC_TO_UNITS(7.5, UNIT_1_25_MS)
#define MAX_CONN_INTERVAL...
My code is as follows:
APP_GPIOTE_INIT(4);
retcode = app_gpiote_user_register(&gpioID, 0, (1 << INT_PIN_MAXIM), interrupt);
The latter function call seems to fail with...
I have check the mesh feature on below link:
github.com/.../nRF51-ble-bcast-mesh
But it seems to work under SDK8.0, how can I make it work with SDK11 and SD130?
Thanks...
To all,
I looked through the nRF52832_PS_v1.0 product spec and I can't find any power consumption numbers for Flash erase. Does anyone know what is the Flash peak current...
I'm trying to migrate a BLE peripheral app on nRF51822 from SDK 10 and s110 to SDK 11 and s130.
I saw that the new Peer Manager does away with pstorage in favour of fstorage...
We designed a BLE device (based on SDK v10.0.0 + SoftDevice S110). From this device we do a few notifications (through sd_ble_gatts_hvx) between two connection intervals....
Hello I have some question about Keil uVision and Nordic Semiconductor SDK.
My development platform is Keil uVision v5 and my target board is nRF51-DK
I've studied many...
I can't find sample code showing how to send multiple packets per BLE interval.
Can someone share an example or point to one in the SDK?
Thanks
Hani Abidi
