Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi there,I am using s130, my device is now working at peripheral mode, it's advertising. I want to switch it into central mode by pressing a button. and switch back to peripheral...
If I had two devices, one set up as a peripheral and one as a central, what sort of factors do I need to consider to work out the lowest possible power consumption/average...
Hi,
I am sampling 2 200Hz signal using ADC and transmitting data using heart rate and battery service of ble_hrm(instead of using simulated data).
But since the connection...
I have the following setup:
nRF51 dongle
connectivity_115k2_with_s130_1.0.0.hex firmware
Windows 7 PC
nrf51-ble-driver_win_0.5.0
My app is written in...
Hi,
I see that you provide Master emulator API for windows (dll) that works with firmware for Master control panel application. Master control panel firmware, as the name...
Hello,
I try to set up an external signal for the LFCLK on a nrf52832. From this question :
I know the nrf52832 can do this (signal on XL1 pin, XL2 grounded).
...
Hello,
I am working on development to concurrent multiprotocol: BLE+2.4G proprietary. I am using timeslot feature in S132.
Because in my own 2.4g proprietary protocol, the...
I want to use feature reports in my HID project, but as far as I see this functionality is not fully included in ble_hids.c (SDK 11). I already managed to properly receive...
Hi,
I want to advertise in variable intervals and mostly only one advertisement at a time. I planned to do it like this:
1- start advertising with any interval (e.g...
Hello,
I followed the example for doing 128 bit UUID advertising using ble_app_uart example. The problem is, this seems to work if I run it when the radio and controller...
Hi,
I have my custom nRF51822 board based on Raytac MDBT40-P module. I am trying to program it with nRF51-DK(PCA10028). I could program it with mbed interface once or twice...
Hi,
I want to implement Advertising with the Timeslot API. I only need non-connectable advertisements but I want to be able to control the transmit power.
Which example...
Hello all,
I would like to understand advertisement packet more.
if I add the following to my packet my firmware causes nrf51822 to crash.
advdata.include_appearance...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
