Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi nRF support team,
I am trying to add a new Custom Service and Characteristic an application on nRF82540 development kit using the nRF Connect SDK.
Can you please let...
Hello.
1. The nPM1300 PS v1.1 states in Section 6.1.1 the fllowing: "The default current limit is IBUS100MA (100 mA)". But the values after reset in registers VBUSINILIMSTARTUP...
I have finally got FOTA working with external flash, but I have a strange problem.
When the FOTA is complete, the mcuboot fails, but the new image boots correctly.
So...
Hi, I am trying to change the USB CDC/ACM com port name. I have read through some posts but they are very short or unanswered. It seems we can change the .inf driver file...
Hello everyone. I work with nrf52840 chip and previously I had an app with softdevice (s140) and use BLE bootloader. Everything works as expected. Next I want to use another...
We are using ncs 2.6.0 and nrf5340 audio dks.
Sample is nrf5340_audio broadcaster.
One dk is configured to work as Audio Broadcast BIS Source and other as Sink. By default...
Hi there,
I am working on an audio recording and transfer application using nRF5340 (microcontroller development kit) and SPH0465 (digital microphone with I2S support...
Hello, I have designed my own board based on NRF52840-CKAA-R, which uses USB power supply. The working voltage of NRF52840 is 3.3V, and my test voltage is normal But NRF52840...
Hi,
I've ready many threads and docs on NRF52 SoC Revisions and Softdevice support but I am still confused. So apologies if I ask something which is already asked.
From...
Hi,
I want to implement low-power mode in my nRF5340 application. From what I understand, Zephyr's idle task automatically handles entering sleep modes, and the device wakes...
Hi,
I am evaluating warm and cold reboots, I am seeing no difference between them. I tried tracing sys_reboot definition, ended up with
For arm core with no handling...
As described in the docs.nordicsemi.com/.../powersave.html: “The application must choose the right duration based on the traffic pattern. Applications must also take appropriate...
Hi, I am using nrf9160 DK development board, i want to use gpio pins in this kit for a SPI interface from nrf52840, which pin i can use for this purpose. in datasheet it very...
Hello Nordic Team,
I am working on integrating the nRF21540 RF Front-End Module (FEM) with the nRF52840-QFAA in the 48-QFN package. Could you please provide the following...
