Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi,
I have a BLE Mesh network managed by an nRF52840 device (let's call it the central device). I can add and remove other nRF52840 nodes to and from the network (kind of...
Hi,
I’d like to implement firmware updates where a central device (SMP Client) updates a peripheral (SMP Server) over Bluetooth.
I came across this repository: github...
I’m currently exploring peripheral support on the nRF54L15 and nRF54LM20A series controllers. I need to turn an LED on and off using the PWM component. The LED is connected...
We are developing a device based on the nRF5340 with an nPM1300 PMIC. The device has three power modes :
Active mode: most peripherals are enabled, and BLE communication...
I want to send Advertising packet with non-connectable and non-scannable via 2.4G without using the Bluetooth protocol stack. I try Congfig Nrf52832 's RADIO ,but it didn...
Hello
I am looking to use [as much as possible of] the full-speed USB bandwidth of 12 Mbps (or 1.5 MBps).
I have been able to use the USB MSC for my initial testing (with...
Hi All,
VS Code version 1.105.0
Mac Silicon, latest OS version installed : Tahoe 26.0.1
Since yesterday, my "nRF connect for VS Code" extension is stalled : the...
Hello, I came across the Location Services page for nRF Cloud and noticed that it supports multiple location technologies, which is quite promising. One line that stood out...
I recently started tooling with Zephyr for low power Bluetooth applications and i was trying to build with sysbuild mcuboot togheter with my nRF52832 without success. I see...
Hi,
I see that Nordic’s nRF Connect SDK now supports the Google Find Hub (Find My Device) SDK.
My question is would it be possible to build an asset tracking solution...
When we were configuring SDA in the visualized device tree, we forgot which button for SDA we should click (as shown in the red box in my picture). Now all the buttons for...
Using the matter weather station as a base on a thingy53 and SDK 3.1.0 which should use matter 1.4.2 if i open zap-gui and try and add a Control Bridge (0x0840) i get notification...
Hi,
1.Please troubleshoot the issue and identify the cause for no response when sending AT%HWVERSION using the merged_serial_lte_modem_v3.0.0.hex and mfw-pti_nrf91x1_2.3...
Hi,
I am currently working with Trusted Firmware-M (TF-M) on an nRF device and trying to understand the design difference between Internal Trusted Storage (ITS) and Protected...
I have encountered a problem with I2C bus on the nRF54L15. BMP390 sensor is connected to nRF54L15-DK by the i2c bus. if i try to brake the line and recover it agane, the connection...
