I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi
I have a question about using gazell link layer and paring library with concurrent timeslot api. I try to do this but i have the hard fault handler after invoked nrf_gzll_init...
HI,
I want to use PWM to control various hardware (LED's, etc ..) so I started off from the suggested PWM code example, found in this forum + modified it as I want to use...
hello,
the function ble_stack_init () in the example of ble_app_uart are quite different from that in the example of ble_app_proximity in my first sight.
ble_app_uart :...
Hi,
I'm working on a project that utilize the MAC library.
Coordinator with non-beaconed mode was previously used in the project, however the NRF 17.1.0 SDK is not compiled...
What is the threshold voltage on a nRF52840 GPIO to detect low level powered with 3.3V?
Can't find it in the datasheet. High level threshold will be 0.7*VDD right? 0.7 ...
I used to use the ncs1.2.0 SDK to develop a product for customers. Now I am porting it to the ncs1.9.0 SDK. During the adaptation process, I find that its control over SPI...
Hello,
I have a few queries:
I need to confirm that does Thingy53 board support TensorFlow lite. So, for my ongoing project, I am using TensorFlow to develop my code...
Hello,
I am facing an issue at running otbr docker conainer on my RPi4 with nRF52840 Dongle as an RCP device . I am getting this error on the logs: Aug 24 16:05:07 0e6bb978e199...
Hi!
I have tried to get the secure_bootloader working on the nRF52820, but I think the linker settings are not correct yet. Maybe someone here has already written a bootloader...
Hello,
I am trying to build OpenThread Radio Co-Processor (RCP) firmware for nRF52840 Dongle with the new nRF Connect SDK v2.0.2. My VM is running Ubuntu 20.04.3 LTS with...
Hello!
I have an application that makes use of the function sd_ble_gap_conn_evt_trigger_start() , present in v7.3.0 of the S113 , S132 , and S140 SoftDevices. Here's the...
Hi,
1. I can use Programmer in nRF Connect for Desktop to flash the hex file ( nRF5_SDK_17.0.2_d674dde\examples\dfu\secure_dfu_test_images\ble\nrf52832sd_s132_bootloader_buttonless_with_setting_page_dfu_secure_ble_debug_without_bonds...
Hi,
I want to use the MCUboot for the DFU and I have been able to configure it and flash it on the device so far (tested that it is correctly flashed).
But I need to make...
Greetings,
I want to write the nRF Connect SDK v2.0.0 sample "nrf9160/https_client" to the nRF9160-DK, but when I use "Flash" in Visual Studio Code, the following error...
Hi,
I'm designing a drone based on these three Nordic IC:
nPM1100
nRF5340
nRF21540
Let's Start with nPM1100:
Based on this Reference circuitry
I based my...
On SDK 2.0.2, I was able to load peripheral_uart with CONFIG_BOOTLOADER_MCUBOOT=y and successfully update both the app core and net core using the thingy53. However when moving...
