Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I'm learning whitelisting with the HID Keyboard Example nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_hids_keyboard\
Question - is there a way to create a new...
Hello,
I'm trying to evaluate a project that works on the 52832 to see if its an easy port yo the 52805. However, I can't seem to find a base make file to start from. I...
Would like to know what is the status of the FCC (CE) certification of the nRF52840 Dongle PCA10059? I know there are various modules available that are FCC/CE certified,...
Hello,
My goal is to use the Jlink JTAG for programming custom nRF52 boards (specifically, nRF52840) using minimum number of wires. The default Jlink JTAG is a 20pin connector...
Device: nRF52833
Board: nRF52833DK
SDK: 16.0.0
Soft Device: S140 7.0.1
IDE: SES for ARM v5.34a (64-bit) - Nordic Edition
Description of Issue:
I'm using the radio...
I am using nrfutil version 5.2.0 with Python27. I attempted to build several times and I got the same error. Please let me know what is " mergehex failed for an unknown reason...
My nRF52840 was recently corrupted. I was able to run through reset and downloaded the latest MCU 'J-Link OB-SAM3U128-V2-NordicSemi 170724.bin' onto the board. So now it shows...
We are preparing a product (based on nRF52840) for manufacturing and currently defining the production test process.
The product is hermetically sealed with no external...
Hello,
I'm currently implementing a multi-endpoints Zigbee device using an nRF52840.
This device is a router which have several "GROUPS" clusters (one in each endpoint...
Hi,
I've nrf52840, s140 with SDK17.2 and I was able to set REGOUT0 to 3.3V in 2 ways.
or
nrfjprog.exe --memwr 0x10001304 --val 0xFFFFFFFD
After that I do...
It is my understanding that the more antennas you use for AoA the more memory is required. I am trying to gauge how much memory and resources would I have left for other application...
Is there a way to configure the serial LTE modem application to communicate through the UART using a 2-wire Tx/Rx with Hardware flow control disabled?
I have read that you...
We are trying to switch main MCU that we use in our products into NRF52/53 series devices. We've chosen NRF52833 (aQFN73) for one of these devices. Is it possible to use only...
Hi,
I have a question about the LwM2M Client implementation for the nRF9160.
Can the LwM2M Object updated in a registration update or it is relying on a re-registration...
I have a situation where a customer needs to DFU some nRF52840 custom boards that we shipped. The firmware that I wrote used extended advertising and thus appears as a Bluetooth...
