Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi,
I want to receive UPD message on my nRF9160-DK. I can send UDP messages from my Nordic device to a server and from that messages I get the public IP address of my module...
I want to use I2S on nrf9160. I found some code on the its user manual and try to run in my project. But when the device is running, it always reboots. What other configuration...
Hi,
I am developing a project related to transferring audio in low energy Bluetooth. I came across nrf connect sdk is the best one for LE Audio transmission
But I am familiar...
Spent a day to build the mesh nrfutil tool. Write down the key step for remind others
Build in windows, No idea for install py2exe in ubuntu python2.7
Use python2.7, do...
I m using nrf52840-DK Board.
For CTL example i got the perfect output on board LEDs 1 to 4.
Then i cut the solder bridge (SB5-SB8)and then used GPIO pinout for external...
I studing a project which is developed on ble_peripheral example. There is using nRF52832, sdk 15.3.0 and s132 softdevice at the project. There is a mobile device, nRF52 and...
Hello
NRF52840. SDK5 17.0.2
the function sd_nvic_SystemReset is define like this:
but NVIC_SystemReset is declared as NO_RETURN which cause dozens of "statement...
Hi,
we're developing a firmware for the nRF52811 that makes exhaustive use of RSSI sampling during packet reception. While this gives reliable results for Nordic proprietary...
Hello,
I'm currently using fatfs with a QSPI flash device on an nRF52840 with SDK 16. I was wondering what is the best way to put the qspi device to sleep in between reads...
Hi, i have a project with NRF52832 and i try to designing 2.4GHz antenna on PCB. I use your antennas as an example while designing, but whenever I try to simulate these antennas...
The company I work for wants to make a wearable personal (care)alarm device for use outside, think of an elderly person who is still mobile but is prone to falling. This device...
hi
All video I can found from youtube and nordic website :
(such as https://www.nordicsemi.com/Software-and-tools/Development-Tools/nRF-Mesh/GetStarted#infotabs )
are...
HI,
I'm facing a weird issue where the nRF52832 breakouit would reset and upon reading the RESETREAS reg, the value is 0xC or 0X8 ,I am using s132_nrf52_4.0.2_softdevice...
Hello,
I am using nRF52833, nRF Connect SDK v1.4.2.
I have imported the Zigbee light switch, light bulb, network_coordinator build and test it successfully.
I have also...
