Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Dear Sirs
We are planning to have our end product certified by FCC and CE. It uses the nrF52840 SOC directly on our PCB. This has the following QDID : 124988.
We have...
I am using cjmcu 8223 board for my project so for uploading program I brought a ST-link V2 pen drive like device but I can't able to detect the board on the ST-link software...
Hi
I am currently evaluating a 52840-DK (from 2017 I believe) and several 52840 dongles (ordered very recently). I managed to successfully run the light/switch mesh example...
Hello,
I'm trying to port the radio synchronization to a nRF5340. For this i need to use a DPPI group that clear a timer and disable itself for doing the task only 1 time...
I'm getting an undocumented status value back from nrfjprog when I try to program my dev board:
ERROR: command exited with status 3221225477 : nrfjprog --program C:/mdsg...
Hi,
I'm new to Nordic tools and am stuck on getting all the pieces in place. I have:
Mac OS 10.14.6
nRF Connect v3.6.1 Getting Started Assistant
Python 3.6.3
All...
Hey Guys,
Transferring emulated project
Transferring an emulated project to the nRF52810 SoC,
If you have developed your application using the emulated project...
Hello,
I am trying to setup a Project with nrf25840 by using the nRF IEEE 802.15.4 radio driver in multiprotocol mode with ble. ( https://github.com/NordicSemiconductor...
Hii guys ,
I have a customised nrf module based on nrf52810 . I have dumped ble_app_beacon code and it works fine but when i dump ble_app_uart example code then i am not...
Hi
I have a question about peers deleting.
It is saying in documentation about pm_peer_delete:
"Warning Use this function only when not connected to or connectable for...
hi Support team,
I have one problem with window7 system both 32 bit and 64 bit, that the usb cdc driver can not be verified by windows, that software signature is not right...
hi support team,
customer has one question about TWI electricity. in the IIC spec the "tLow " should be more than 1.3 us
however, our chip interface TWI timing " tLow...
Overlapping segments detected at address 520192.ERROR: The hex files cannot be merged since there are conflicts.
should be
Overlapping segments detected at address 0x...
I’m obviously missing something from the information I’ve gathered with respect to designing a co-planar waveguide, PCB 50 Ohm transmission line. The calculations I get differ...
