Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hi below is the function i am using to run garbage collection after deleting the data but the result i am getting was the same as before garbage collection.
I mean DIRTY_RECORDS_BEFORE_GC...
I have the following questions about PM and what it generates. My relevant board and config files are below, along with the PM partitions output.
1. Can you explain the...
I am using SDK v17 and Segger v4.52 but for some reason none of the print statements are being printed in the debug terminal. I think I had to enable these two things in sdk_config...
I am sending or trying to write character to ble_app_template but its giving error and its not receiving character.
this what i am trying to send-
if(strcmp((const char...
I see an ID that queries or prints RSRP/RSRQ/Cell ID-related information, but I don't see the AT instruction sq.E. for SINR, where can I print SINR information?
Hello guys,
Just received the Thingy91 and trying to upgrade the model firmware to v1.2 but it fails like this:
However I successfully been able to flash the modem firmware...
Hi Team,
We are using the nrf52840 soc for our application along with crypto engine (mbed TLS ) along with RNG, ECC, SHA256.
While validating the digital signature with...
Hi,
Do you have any direction finding evaluation kits for now? Although I saw many similar questions and until four months ago the answer is still NO, but I still want to...
we'r developing our product based on nRF51822 and also using BLE(Bluetooth) as wireless device.So, we want to release our first product in this year in markets. The next steps...
Hi Forum, 1.) The APP_ADV_... parameters in ble_advertising (SDK 16.0) are taken only from _fast_ , is this intended?
2.) s113 allows only TX_POWER of 4dbm, although the...
I would like to flash certificates in production.
My plan is
First, flash an app for installing parameter like client id using nvs and certificates.
Then, flash a production...
Hello,
As of nRF Connect SDK v1.3.0, I now get an additional output target called "merged_domain_hex". I don't recall this being part of the output prior to nRF Connect...
I am working on a design that has an nRF9160 being powered by a a 3.6V lithium primary battery. I know nRF9160 VDD is 3.8V(Nom.) Is there any problem in LTE RF performance...
Hello.
I use SDK16 in my project.
Previously when I want to go on sleep I use __WFI(), and get into sleep till interrupt. Because I use The SoftDevice I change the command...
Hello,
nRF52 supports Systick timer. But I can not find information about it in the "nRF52832 Objective Product Product Specification". Is it currently open for user ?...
