Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
I am struggling with the Zigbee SDK for the nRF52840. I have successfully run the light switch demo with the PCA10056 board as the switch and two dongles behaving as coordinator...
I have been struggling to get a Zigbee end device talking to a SmartThings hub which is on channel 14. I have now discovered that regardless of the channel mask I give it...
I followed instructions given here https://devzone.nordicsemi.com/b/blog/posts/segger-embedded-studio-a-cross-platform-ide
I got it working in Build and Debug mode. However...
Dear Sir,
I am calling the function sd_ble_gap_disconnect() to disconnect the peripheral from the App.
This is called inside ble_evt_handler() function and under
...
I'm looking for Memory LCD shield like using nRF52840 long range demo.
The shield name is probably PCA63520. However I can not find it.
Where can I get it?
In the folder for the sd_api_v6 there are the headers for the softdevice S140: pc-ble-driver_v4.0.0\src\sd_api_v6\sdk\components\softdevice\s140\headers
I have a custom...
I want to use the CUSTOMER[] fields for their apparent intended purpose of storing calibration data in nonvolatile memory. I find it quite absurd that the softdevice would...
Hi,
I am using PWM to control LED power.
The code i use for initializing the PWM is-
app_pwm_config_t pwm1_cfg = APP_PWM_DEFAULT_CONFIG_2CH(1000L, PIN1, PIN2); err_code...
Hello,
I am trying to run the example DFU over TFTP. I have setup a tftp server with following configurations:
# /etc/default/tftpd-hpa TFTP_USERNAME="tftp" TFTP_DIRECTORY...
Hi,
I've followed the link https://devzone.nordicsemi.com/f/nordic-q-a/35675/how-to-use-static-passkey-for-a-no-display-no-output-peripheral
and added it to uart example...
Hi,
My app requests a timeslot in various conditions - sometimes the timeslot needed is long, sometimes short (unknown a priory) so it asks for the longest possible...
Hi,
Is there any easier way when using Eclipse IDE with GCC for nRF5 SDK 15.2 development to get the Include files in the examples to be recognized easier than tediously...
My set up contains beagle bone black as Application board. PCA10001 board with S120 Softdevice using nordic_sdk_10 running ble_connectivity example program.
I initiated...
I have a Teledyne protocol analyzer for capturing over the air data between an nRF52840-DK and an iPhone 8 device. How do I obtain the encryption key from the nRF52840 SoC...
Hi,
I want to verify Bluetooth on my board is good or bad.
Note that, I do not have any spectrum analyzer or vector network analyzer, just development kit.
I found example...
