Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hello is a starter developer
I used the nrf51822 chip on the pcb board and downloaded the example code but it did not work.
When I checked the 16mhz external crystal on...
Hi all,
I am a bit confused about the use of SOFTDEVICE_HANDLER_APPSH_INIT and similarly APP_TIMER_APPSH_INIT. I've not been able to find anything in the documentation...
nrf52840, S140.
So for the past 1 or 2 weeks I have been fighting with this problem :
Now it turned out that the connection handle may actually be INVALID, it's 0! ...
I am using nRF52840 DK as a SPI slave with an external MCU configured as SPI master. The SPI clock frequency is set to 1 MHz. I am using the following pins for SPI:
P0...
Hi All,
I have just got my nRF51 kit (S130) and started working on a beacon project which would transmit advertisements packets from peripherals over a RS485 to a server...
Hi,
im running my DK as a central of a BLE connection and i'd like to read the device_name of the peripheral board that im communication with. how do i do this? i cannot...
Testing on nrf52DK (QFAAB0), without softdevice, unfortunately still on SDK10 and
NRF52 sleeping on RTC. Programming pins disconnected.
Measured:
low frequency clock...
i am total beginner to the nrf51822. i am going through the nan-36_v1
app note is using s110 but i can't find that soft device in sdk ? is there any changes has to be done...
Hi,
I took the ble_hrs_c code and modified it such that it has the NUS service and can connect to 2 peripherals. The code works when I power cycle the central+2peripheral...
hi Engineers!
I am trying to use int. pullup of 160k but no effect. the voltage remains zero on pin.
config.resistor_p = NRF_SAADC_RESISTOR_PULLUP;
what problem?
...
Hi All,
sometimes i have a problems with bonding: the Nordic APP said "Couldn't pair with xxxxxx because of an incorrect PIN or passkey".
Why i have this errors? What...
Hi guys,
i'm trying experimental_ble_app_queued_writes out. I have some strange behavior.
The qwr service is
6e400001-b5a3-f393-e0a9-e50e24dcca9e but the characteristic...
I am developping NUS server(Peripheral) on Android. Central is ble_app_uart_c on nRF52832.
In this case, service discovery cannot be completed.
According to the console...
Hi. I am new with KEIL MDK and Nordic and ARM .....
I will create an MIDI BLE, but maybe anybody has an working Example for this?
Or what for an Example i can modify?
...
