I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi, I'm working on a project where I'm trying to make an nRF51822 play a basic sound (such as a beep). Is there a recommended DAC that should be used with this particular...
hi, i am using nrf51822 version 2, SDK 6.1.0, softdevice version 7.3.0.
because the nrf 51822 is version 2, i have no choice but to use SDK 6.1.0 not 11.0.0(latest version...
hi,
i am using ble_uart example for send 3 byte (midi format) of data over uart.
i am receiving data which is appended with past data and sends as a chunk of data around...
Hello, i'm making small android application for my own test purposes. I want to understand full structure of advertisement packet which i receive with my phone. I can't find...
Hi.
I'm using nRF51822 with softdevice 8.
I started working with the uart example. and it works fine.
However, I can't get the BLE to reconnect automatically once the device...
Hello, i'm working with nrf8001 right now. I know that nrf8001 can work like Peripheral(slave) device. This is working ok. Im wondering if it is possible for nrf8001 to work...
Hello I'm trying to utilise the multiceiver mode with nRF24L01 and Arduino, the idea is that an nRF will be able to send a message and six other receivers will be able to...
When I use nRF UART of android phone A and B to scan the bluetooth device, the scan result is below:
first picture is the result of phone A, second is phone B:
first one...
Hi,
I want to use nrf51 development board as a bluetooth alarm clock using internal RTC . How can I generate timestamps to determine current date and time. Can the timer...
hi.
i want to parse the data before sending to BLE UART.
i am fetching data from RX/TX pin. and now i want to do some modification in data before sending it.
this block...
Hi, I want to send a constant carrier during production testing of a product.
First I call sd_softdevice_disable(); then I do the following:
//Restart radio
NRF_PPI...
Hello,
in our application I can see, that sometimes the nRF51822 completely resets, during a BLE transmission.
I am using S120 as peripheral. The peripheral is connected...
Hello,
I am trying to understand the basic working principle of the bootloader so i tried the DFU example in the SDK 9 it gets compiled and when i try to flash into the...
Hello,
I am using BL600A module and Nordic softdevice and SDK9.0. The system is having NUS service and TX and RX characteristic. Now I have a requirement for firmware upgrade...