Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I started by compiling BLT uart app successfully on MDK5 but found out that it is giving errors on the startup files in the Device Pack.
I tried to refresh and update Device...
Hello Everyone,
I am trying to measure the (3v)battery voltage by having proximity example as reference but intially it is showing 100percent later it is going to 13(percent...
Hi,
SDK: v11.0.0.2-alpha
DK: PCA10040 (NRF52)
I am trying to build a peripheral application that communicates with an external device via UART (h/w flow disabled)....
Hello!
I have PCA10006 with revision QFAA nRF51422
I am testing the buck converter's ability to make the system consume less power when transmitting.
Example is ant...
hello there! i am working on project in which my one nordic BLE(A) want to send command to second nordic BLE(C) which is not in my range. now there is third nordic BLE(B)...
Hello Guys,
I would like to know, can i use NRF52 Preview DK on Board Segger Section as standalone Segger JLink Programmer for NRF51?
So, is there any way to dis connect...
Hi, I read about concurent operation of the Softdevice and other proprietary stacks like esb or gazelle using timeslot api. Is it possible to run two ble stacks in this way...
Hi Guys,
I would like to develope a HID device on nRF52832 chip. I'm woring with nRF52 Development Kit (PCA10040, v0.9.0).
I've tried to flash the board with both hid...
I'm getting the NRF_ERROR_NO_MEM when I try to put my ADC interrupt routine into the scheduler. The code runs without error if I run from the ADC interrupt handler directly...
Hello ,
I am testing the DFU support and usage for the next phase of my project. I am using S110 softdevice 8.0 and SDK 9.0 and evaluation kit nRF51822QFAAG0.
I followed...
hello, I have some quesetion about the nrf51822's carrier detect. I want to use " CSMA" to avoid
Communication collision, the datasheet has no detailed infomation about...
when I call pstorage_store so store a block of data, sometimes I call just after pstorage_store : the following code
do {
pstorage_access_status_get(&count);
} while...
In this post , I can register a new case with some required parameters to have the current estimation, but I don' t know how to obtain some of them.
I'm using nRF51422...
on the log of nRF Master Control (mobile version) I can see DEBUG VERBOSE APP WARNING . I want to know if there is a directive on SDK 10 (functions) to send those kind of...
I created a BLE central device using nrf51422 chip base on S120, it connects to a peripheral device which can send around 12k bytes in 10 seconds. My device always received...
