Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello,
I am currently working with the Matter lightbulb example in NCS v2.9.0 with the nrf5340 (Raytac MDBT53-DB-40). I have gone through the project tree and added overlay...
Hi,
I have been trying to modify the LVGL example to work with an 480x320 SPI TFT screen (adafruit's 480x360 TFT featherwing specifically). I have gotten working with 240...
Hi,
I cannot bond to NRF5340DK running the `peripheral_ancs_client` sample if external oscillator configuration is disabled (thus using synthesized from HFCLK).
Environment...
Hi,
Iam trying to implement multirole ble in nrf5340 using ncs. I am using legacy advertizing type for advertize and observing both.
why it is working only first time...
Hi nRF support team,
In my application, I need to show system date and time, so I am trying to get the system epoch time by using the nRF Connect SDK on nRF52840 dev kit...
Since I am a beginner with Zigbee, I would appreciate your guidance.
Currently, I am using the nRF Connect SDK v2.8.0(Zigbee-addon) with the nRF54L15 to work with Zigbee...
Hi there. I'm attempting to do trilateration between 3 nRF Devices. A1, A2, and A3.
A1 - A2 I can get using the nRF Distance Measurement toolbox
A1 - A3 I can get using...
We have implemented a simple contact switch using the nrf52840 and the latest zip generator (v99). The device connects to a Samsung Smart things edge router. A contact device...
Hello Nordic Team,
HW: nRF52840DK
SDK: ncs v2.8.0
App: hci_pwr_ctrl
I am testing with hci_pwr_ctrl example to see how tx power can be set from application.
The...
I am working my way through the Beginner course on Dev Academy, and am trying my hand at using my own accelerometer breakout board communicating over I2C for lesson 6.
I...
Hi,
I have used course's example for GPIO interrupt for toggling LED and used to update BLE adv parameters without using DK buttons library. But, as soon as, I update BLE...
Hi there, I'm new to the nrf/zephyr sdk and while using the nRF5340dk board, I've found that the pin1.01 is pulled high right after the board powers up. My assumption is that...
Hi All
Hi, I am using nrf51822 controller in my design for with SMD chip antenna for RF output.
Can anyone suggest me any reference design(Hardware and Layout files) to...
I'm attempting to initialise my first zephyr project using the nRF SDK, and have been following the academy course on the nRF boards. Problems arise on the install SDK (2...
Hi,
Only the TX and RX of NRF52840 chip UART are used to test OpenThread CLI Demo. How can I change the configuration of UART in the original CLI Demo?
Thanks.
