Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi,
Im trying to send 20 packages of 30bytes each as fast as possible, so I created the following loop:
for( pack=0; pack<20; pack++)
{
w_tx_payload_noack(30, MegaBuffer...
Hi all,
I have a custom board with the Nrf51822 BLE chip and it works in broadcasting mode without connection only. Basically it sends the advertising data on an established...
Hi
I have some problems about using your Master Emulator API. I want to write a dynamic link library with C++, but I don’t know how to invoke the MasterEmulator.dll.
The...
I'd like to use LPCOMP. I'd like to get rid of the 12K pulldown on SWDIO.
I can tell from PCN-082 that QFAA CA and C0, as well as QFAB AA and A0, will let me do that. ...
hello,
I know the ble device ,have central and peripheral and have some name(server/client and Observer/ Broadcaster).
The peripheral(server) has data that is needed by...
I put the boot loader at 0x3a800 and the application at 0x27400. the region from 0x14000 to 0x27400 is all blank (0xff). also
nrfjprog --memwr 0x10001014 --val 0x0003a800...
Hi,
I need to pair with the master after pressing the button in my slave device, instead of asking for passkey. Through the master control panel, i can able to see that,...
Hi,
Actually in our application we have connect accelerometer sensor to Nordic by SPI. I'm calculating power consumption for it. In datasheet it's mentioned for SPI Data...
Hello to everyone,
My problem/question now is about the MasterEmulator. I´m working with the nRF51822(SoftDevice) and i have my own program already working more or less...
Hi
I am a newbie to the bluetooth technology. I want to ask some questions:
How to apply a LLS(lost link service) profile to a bluetooth module?
Can I buy the...
After reading devzone.nordicsemi.com/.../is-there-any-differences-between-nrf51822-and-nrf51922 and the literature around nRF51922, I'd like to know if there's going to be...
Hi,
I've developed an application which sends sensor data through the BLE interface at maximum available bandwidth by checking the BLE_ERROR_NO_TX_BUFFERS return value...
Hello,
I was wondering if anyone has had success communicating with the nRF24L01+ eval kit and a Raspberry Pi. I have found several examples through Google and am trying...
I am requesting the softdevice to start/keep the 16Mhz crystal oscilator running with the following code:
// Request 16 MHz crystal oscillator
err_code = sd_clock_hfclk_request...