Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hello,
Its me again.First of all I want to say thanks to HÅKON ALSETH, with his help I was able to work with hardware interrrupt. now I am facing another problem, I need...
want to FLASH upgrade FW in the nRF51822 though my application controller. Is C or C++ code available for this operation or can you deliver a protocol description how to setup...
Hello Everybody,
I am new to Nordic and Bluetooth. I see nrf51822a have BLE + Cortex MCU inbuilt and this suits best to my application.
I have some doubts regarding...
How do I use nRF51822DK without "nRFgo Starter Kit Motherboard"? I have read "nRF51822 Development Kit User Guide v1.2" and have no result how can I only use nRF51822DK hardware...
Dear All
i would like to use
nRF51822
nRF51422
i would like to use nordic product,
but so shame, too low basic knowledge for make program for embedded, edit library...
Hello,
I attached the schematic found in the manual for NRF8001, in the case of DC/DC converter enabled.
It shows that an external 32.768KHZ crystal is used, while in...
Hello, I have major problem trying to debug/run ble_app_hrs example. The thing is that when I enter debug mode the code is stuck here:
0x000001B4 4908 LDR r1,[pc,#32...
Based on nRF51822\Board\nrf6310\ble\ble_app_hids_mouse example,
Used hid consumer page function, like play/pause or volume+ or volume- ...etc function,
In nRF51822 device...
I can't seem to find the hex file to download into the PCA10000 in order to use it with the Master Control Panel. Where is this documented in the dev-kit documentation?
Hello, I'm M.S. Candadate in Korea.
I have a Question.
I heard that nRF51822 can operate only as Peripheral role and can't operate as Central role.
Now, Does it operate...
My project has moved off the devboard and onto prototype PCBAs. I notice that they all seem to have unique MAC IDs on the air! I'm not complaining (one less thing to worry...
So i am using a LiPo battery at 4.2V and running my nRF51822 at 2.0V. Is it safe to connect the battery to one of the I/O pins to read off the battery voltage (as to calculate...
Hi there.
We are developing an IoT device (we are planning to use nRF24L01+) we would like to implement with microchip uC, the question is if there is a library available...
