My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
Hi,
I need to have long attributes. So I need 'Read Blob' operation for read and Queued writes ('Prepare Write' and 'Execute Write'). Does Soft Device for nrf51822 support...
Hello everyone , can i use UART which is not a services or characteristic in bluetooth low energy . It will result in some question or bad effection?
By the way . why I cannot...
Dear all:
recently, I follow heart rate profile to write custom BLE profile,but I also went to a number of issues. how to wake up the device when entered power system off...
Hello,
This is the first time i use NRF8001 chip, i was reading the ic manual nrf8001_PS_v1.1.pdf (see attached file).
It was written that in case i used DC/DC converter...
Hello,
I checked Nordic website for layout of NRF8001 but i didn't find.
Please if some one can share a qualified RF-layout.
Help is appreciated.
Regards,
Hisham
from training document from Nordic company(see the attachments),it mentioned that we can add scan response .but i can not find any information in BLE_HRS demo.could you tell...
Hello,
I made a PWM with the TIMER2 of my nRF51822 (with the SoftDevice) and was working fine, till I read that I should not use the "NRF_PPI" functions and use the "sd_ppi_XXX...
I've got an nRF51822 development kit that I'm trying to get started on. I've gone to Kiel and downloaded uVision 4 (mdk472_a). I install it with all default settings and it...
Hi,
I add UART support using IRQ on the "ant_hrm_tx" example code.
and I'm sending packet of 4 bytes that contains: Delimiter,HeartRate,Battery,Delimiter
the frame...
Hi, I am trying to test my UART using some simple loopback test, and I have noticed that the service discovery command of BLE will occupy the CPU a quite long time. I am just...
I was unaware that the 'manufacturer data' in the advertising packets is limited to less than a full payload. However, whenever I set it to >6 the program "crashes".
...
When I use keil to download the software to the chip, there are two questions:
like attached.
2.NRFGO CAN'T SEE J-LINK LITE CORTEXM BOARD
Is there any way to solve...
We have recently moved to a new PCB which puts the nRF8001 on the layout instead of plugging into a nRF2741 development module. The nRF8001 connects to a TI Cortex-M4 Tiva...
