Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
Hi everyone,
So I have using Zigbee and Thread SDK 4.2.0 for a while and I notice that some time there are some error like this
<error> app: ZBOSS assertion in file: 105...
Hello All,
I have few questions below:
- What is the efficiency of the embedded DC/DC converters in the nRF53 circuit? What is the difference in efficiency when the circuit...
Hello everyone,
In our custom tracking application for the nRF9160, I am connecting to nRFCloud through MQTT when needed. Either when sending a data, or requesting assistance...
Hi Nordic and everyone else!
First my question: I am sending my position data to the cloud in the same matter as the MQTT Multi Service sample. It converts some PVT data...
I have made a second rpmsg endpoint to hci_rpmsg sample and integrated direct test mode sample functionality behind that second endpoint. Application has dedicated test mode...
Hi team,
If the TTL count is 100 but the number of devices in the network is 10. Will the device routing table in BLE mesh SDK understand that the message has been already...
The UART and UARTE peripherals share the same ID (2), and only one of these can be enabled at a time.
How do you enable only one of these peripherals?
The register blocks...
I have MCUBOOT working using the default UART pin numbers. I need to change the UART RX and TX pin numbers used by MCUBOOT for a custom application. I am able to change the...
Want to store the CONFIG_BOOT_SIGNATURE_KEY_FILE in the project space, not the ncs folders.
Looking for a method to define file location without using a absolute path. ...
I am using NCS v2 and VSCode extension on Windows 11.
I have two pieces of hardware I am testing with:
Adafruit nRF52840 Feather
Custom nRF52840 board
When I flash...
OS in development environment ：Windows10 HARD :(Taiyo Yuden)EBSHSN Series Evaluation Board : Central / Peripherals CPU :(Nordic) nRF52832 / ARMR Cortex-M4F 32 bit processor...
I would like to automate some unit tests with NCS. I tried running the native_posix qemu builds, however, this does not support the mac m1 architecture (maybe Linux only?...
I'm updating the NCS we are using from 2.0.2 to 2.1.0 in order to use the modem firmware 1.3.3 that was just released. I verified my build with NCS 2.0.0, 2.0.1 and 2.0.2...
Hello!
I use NRF Connect SDK 1.8.0, but peripherials are configured using nrfx library.
My task is to implement serial interface where I have PIN_TX and PIN_RX. I transmit...
