Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi!
We're working on an AoA application using a custom nRF5340 board and antenna array. Just trying to fully understand the interpretation of IQ data, there are a couple...
I can see that there are others that have had problems with finding SIMPLE information from this site.... I would like to get off on a better footing.
Here is the issue...
I'm considering transitioning a product codebase to the nRF family (nRF52 or nRF53).
It's Arduino code, with lots of C++ code.
As in the cpp_synchonization example provided...
Hello,
I'm having an error with the 832, specifically I'm just trying to port code over from an 833 project. I can compile no problem, but when I go to write I get
ERROR...
Hi there,
I've been working on creating a nice wrapper around the nrf modem library in Rust. Currently can be found here: https://github.com/diondokter/nrf-modem
When...
I was testing out the custom application from android studio, and have discovered that, for example, when using the rscs example my application does not see the device and...
Hi Nordic. This is a general question and could as easily have been posted to stack overflow but I have found the members and staff of this community so helpful and adept...
HI,
I am working on a application which has an requirement, that I need to read the current value if it is above threshold value then I need to turnoff the control. Here...
The executed command at connectedhomeip/examples/lighting-app/nrfconnect: west build -p -b nrf52840dongle_nrf52840
The messages i encountered:
...
/ncs/zephyr/include...
good day,
is there a way to set a gpio when in dfu mode? wanted to make GPIO 19 of nRF52832 HIGH during DFU mode because we assigned it as an enable pin.
in DFU mode,...
Hello,
I have my own custom board with nRF52832 and a NB-iot module SIM7080G that interfaces via UART.
I can easily program the device through SWD using J-Link. I am even...
Hello,
I am using flash_write_protection_set function with few low level function call for accessing extremal flash with nRF9160. And because of that I am facing one warning...
Hi,
I am programming the nRF52833 and using NCS v2.00. I have recently programmed the Peripheral Coded PHY to the board. I am using a Google Pixel 3 with nRF Connect as...
Hi,
Can we use the PPK2 kit for measuring current consumption in any other reference design board from a different
vendor which is not same as DA. The other vendor does...
Dear person in charge.
Before using PPK2 for a evaluation of current consumption, I checkd power supply vs corrent measurement by using PPK2 and 5kΩ chip resistor.
I...
