Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hello,
I'm working on development of custom board based of nrf52811, we are using MAXM86161 and ICM-42605 on the custom board but couldn't find any drivers or library...
Hi, The attached picture below captures all the RSSI of our beacons in the field. These devices were set to transmit at maximum transmit power of +4dBm. This max value was...
Hi
I'm trying to get the application timer working on nrf52840 SDK version 17.02
I have followed the below link
devzone.nordicsemi.com/.../application-timer-tutorial...
I am able to print out to Uart but not able to receive from uart.
what do i get wrong?
/* main.c - Application main entry point */
/*
* Copyright (c) 2015-2016...
Hi everyone,
I would like to overwrite my SoftDevice wchich I don't use in my application. I found information about updates without Softdevice.
Its possible to update...
Hi,
I'm trying to build the SLM application on the SIAA chip (w/o GPS). I'm modifying from the nrf9160df_nrf9160 board, but no success there. Is it possible to build the...
When I set the GPIOE pin to float, NRF_DRV_gPIote_IN_config_t config = GPIOTE_CONFIG_IN_SENSE_TOGGLE(true);
The power difference between true and false is 10uA, but when...
Hi All
I have been successfully using a jlink flasher for quite a few years now but after upgrading the segger drivers as i have always done ever couple of months i now...
Dear Nordic Developer Zone,
Is there a way to set the LFCLK (32.768kHz) on a GPIO using nRF52811 ?
I want to use this clock for controlling another device.
Best reg...
I'm trying to implement OTA DFU in our custom App with our nRF52832 acting as the device to be upgraded. Everything seems to work OK in that:
1. New image uploads to the...
I have configured a composite USB device on nRF5340 with DFU+CDC+Audio interfaces and enabled MCUBoot. Trying to perform DFU using dfu-util tool on Windows always fails. Following...
Dear Nordic Engineers
I have a problem and would like to ask you about the frequency offset of NRF5340.
As we all know, if I would like to adjust the frequency offset...
Hi everyone,
I am currently working with NRF52833 and SDK 17.0. Everythings went pretty well, however, now i need to have some memory check in runtime since i used a lot...
Hi guys
I ve made a custom board using the nrf52811 SoC,and now i want to program it for testing.
The thing is i am really lost on what to do, this is the first time...
I wanted to use SES (6.32b) to build an example app (nRF5_SDK_14.2.0_17b948a, ble_app_blinky) and run it on a Nordic dev board (nRF52840 Development Kit), but crashed.
...
