Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hello everyone,
I am currently using NRF5340dk and I need the Library queue, (I especially need the functions: nrf_queue_push and nrf_queue_pop..). (Knowing also that I...
Hi Nordic Team, I am trying to develop an AOA application using the NRF52833 nordic SOC. I am using NCS 1.6.1 development SDK in Segger Embedded Studio.
I am flashing a...
Hi
I want to measure the battery lithium, this battery is the principal source (3.7v 300mh), the maximum voltage is 4.2 when the charge is full,
i'm using this code for...
Hi
I'm trying to enable BLE host-only build on Application core on nrf5340dk, and also enable RPMsg/openAMP.
I'm using Zephyr and its build system.
I get the following...
Hello everyone,
I'm working on a project right now and I want to use the ADS1298 analog to digital converter and configure it with NRF5340dk. Being a beginner I looked for...
hello,
i'm having an nrf52 based system with an antenna switcher in front of it, for antenna diversity. i tried using BT_HCI_OP_READ_RSSI as basis for my antenna diversity...
Hello, All;
Using your nRF9160 chip to develop, there are some questions when using the network and positioning, Hope to get your answer:
1. Can LTE work at the same time...
Hello,
I have two projects, one for the application core (modified BLE Peripheral sample) and the second is for the network core (modified HCI_RPMsg sample). I am currently...
Hi all:
condition:
SDK14.2
PCA10040
example: ble_app_uart_c
I have a central device ,it need to scan RSSI value of peripheral.
If the RSSI is more than threshold...
Hello,
we were using the HRS example as a starting point and modified it for our application. Everything works fine, we can see our custom characteristics, control our device...
Is it possible, without having to join ZOI, to recompile the Zigbee ZBOSS NCP Host for the Raspberry Pi?
The NRF Connect SDK documentation under ZBOSS NCP Host states :...
Hello,
we have an custom made board with a module from raytec MDBT42q.
Our application based on the nus example.
On port 0.7 we have a led.
It seems, that there is...
Hi
How do I configure a custom child image for the network core on nrf5340dk? We're using Zephyr RTOS, and want to do a multi image build when building the application ...
Dear Nordic,
Do we have ready-to-use keyboard driver with scanning/debouncing?
I've not found an example or docs about using KSCAN with gpio-connected keyboard...
Hello, I would like to know if the Power Profiler Kit II could be used to measure current consumption on the Thingy:91 ?
In the Thingy:91 documentation, it is suggested...
