Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
I’m currently exploring peripheral support on the nRF54L15 and nRF54LM20A series controllers. I need to turn an LED on and off using the PWM component. The LED is connected...
We are developing a device based on the nRF5340 with an nPM1300 PMIC. The device has three power modes :
Active mode: most peripherals are enabled, and BLE communication...
I want to send Advertising packet with non-connectable and non-scannable via 2.4G without using the Bluetooth protocol stack. I try Congfig Nrf52832 's RADIO ,but it didn...
Hello
I am looking to use [as much as possible of] the full-speed USB bandwidth of 12 Mbps (or 1.5 MBps).
I have been able to use the USB MSC for my initial testing (with...
Hi All,
VS Code version 1.105.0
Mac Silicon, latest OS version installed : Tahoe 26.0.1
Since yesterday, my "nRF connect for VS Code" extension is stalled : the...
Hello, I came across the Location Services page for nRF Cloud and noticed that it supports multiple location technologies, which is quite promising. One line that stood out...
I recently started tooling with Zephyr for low power Bluetooth applications and i was trying to build with sysbuild mcuboot togheter with my nRF52832 without success. I see...
Hi,
I see that Nordic’s nRF Connect SDK now supports the Google Find Hub (Find My Device) SDK.
My question is would it be possible to build an asset tracking solution...
When we were configuring SDA in the visualized device tree, we forgot which button for SDA we should click (as shown in the red box in my picture). Now all the buttons for...
Using the matter weather station as a base on a thingy53 and SDK 3.1.0 which should use matter 1.4.2 if i open zap-gui and try and add a Control Bridge (0x0840) i get notification...
Hi,
1.Please troubleshoot the issue and identify the cause for no response when sending AT%HWVERSION using the merged_serial_lte_modem_v3.0.0.hex and mfw-pti_nrf91x1_2.3...
Hi,
I am currently working with Trusted Firmware-M (TF-M) on an nRF device and trying to understand the design difference between Internal Trusted Storage (ITS) and Protected...
I have encountered a problem with I2C bus on the nRF54L15. BMP390 sensor is connected to nRF54L15-DK by the i2c bus. if i try to brake the line and recover it agane, the connection...
In nRF5 SDK, we configure GPIO wakeup sources for System OFF using `nrf_gpio_cfg_sense_input(pin_number)`.
What is the **exact equivalent API/configuration** in **nRF Connect...
Hello.
I'm trying to use a nrf52840 as a central device and connect to a gopro13. The connection works a certain number of times. But after a while (several days or maybe...
