Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I'm trying to measure and log the low power coming from a peltier module. (TEG seebeck effect). In Ampere meter mode with LED for load I get nothing. Replace TEG with...
Hi,
I successful developed a application using nrf / zephyr SDK and install the applications on the nrf52840dk and dongle. Now I want to adjust the power using
CONFIG_BT_CTLR_TX_PWR_PLUS_3...
hello i am trying to interface RN8209c ic with nrf52832 using uart communication with sdk 15.2
uint8_t readbuf[50];
uint32_t err_code;
uint8_t buf[10]; buf[0]=0x7f;...
Hi,
I am trying to modify the Android nRF Mesh app to filter un-provisioned devices with URI hash contained on un-provisioned device beacon.
My question is how I can...
Hi
I have a question, the Nordic SDK have a DFU, I want to know what is the default value of TX power in Bootloader? Can we change the TX power? if yes. How to change it...
Hello, I'm using nrf52805. It is confirmed that P0.04 is AIN2 and P0.05 is AIN3. Can I use this pin as UART TX,RX? What should I do to use it? Thank you.
Hi!
I am trying to work through the nRF Connect SDK tutorial series, and I got stuck at the "building with west step" in part1.
When I try to build my project using the...
Hi guys,
I have a peripheral device using a custom service based on the ble_nus, the intention is to hide the service and its characteristics until the bonded has been...
Recently our Device started exhibiting random BLE disconnect problems.
It's really hard to debug as not all of our devices are exhibiting this issue and in generally so...
Hi
I have a question to ask for your help. I'm studying thread networking. The SDK is "nRF5_SDK_for_Thread_and_Zigbee_v4.1.0" I use masterkey networking, but I find it unstable...
Hi all, i want to ensure my antenna have correctly triggered. I'm using TI Boostxl-AoA antenna for nRF52833, Its a antenna of 6 , but i'm just opening up 3 first. my sequence...
I would like to figure our how i can send MQTT packages over a Thread network using a nrf52840DK. And to begin with only between two nrf52840 devices.
I am using the nrf...
Hi
I'm testing RC3 of NRF Connect SDK v1.6 in combination with our application. I have an issue with the configuration when I want to enable CONFIG_LTE_LINK_CONTROL. This...
