Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
I want to move the uart communication port from default pins to
#define RX_PIN_NUMBER 33 #define TX_PIN_NUMBER 34 #define CTS_PIN_NUMBER 35 #define RTS_PIN_NUMBER 36
I...
Hi There,
How to control led using pwm during dfu mode (when dfu programming is on going).
HW:PCA10056
SW: nRF5_SDK_15.2.0_9412b96
Example: ble_app_buttonless_dfu
I really did not want to ask, howeverI have spent a lot of time on this and still no joy.
I have a epaper shield have got the electronic paper display working. so SPI writes...
Hello,
I see on you webpage that there is an evaluation kit for nrf21540 -> PCA10112 . do you have the schematic of this board ?
For the moment I'm using the NRF52840...
Hi Guys,
We have a need to send data every 4 hours.
In order to do this, we sleep 1 hour at a time (1-hour timer - single shot) and increment counter, and when the count...
I'm using 2 nRF5340PDK with nRF Connect SDK 1.4.0. 1 PDK with central_uart and 1 PDK with peripheral_uart.
When I change the clock config of the peripheral_uart by using...
using nrf-9160dk and iBasis SIM with pre-built asset tracker app (2020-10-30_5522ca2b) and nrfCloud
First time the device was registered data transmission worked.
Now...
The design has 2 sensors on SPI with mode 3 and the nrf21540 which is mode 0. Can you have 2 different Modes on the same spi bus?
would i use the SPI transaction manager...
Hi,
I have the barest of PCBs with literally just the nRF9160, SIM slot and antenna, and have wired it directly to an Otii Arc, so there is no power circuitry either as...
Hi All,
If I want a Thread device to automatically start commissioning when it starts, is there a code example in Nordic SDK?
Now I just found the API interface, called...
NRF52832 is using the protocol stack and updated by OTA. Why should the number of FDS Pages of the new firmware be equal to the number of FDS Pages of the old firmware?
Hi,
I am using NRF52810 , In my project I need to store Float value and uint32_t value in EEPROM / Flash for permanent storage (Non-volatile storage).
With SDK17 i am...
Installing a toolchain for nRF 9160 is not easy as installing the Arduino IDE ( at the leat in Ubuntu). I request Nordic Semi to install all the required tools in a cloud...
Can I buy nrf52811 in bulk and have my bootloader and firmware installed before I receive them for production? And what is the cost say for 1500 preloaded. ?
