Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
Hello All,
We are testing power consumption nRF52810 in system ON mode , my configurations as below,
Device will advertise for 10 sec connect with the mobile app sends...
I have already went through every step as per what the documentation has stated, but I could not be able to sniff any ZigBee packets using Wireshark. I only want to perform...
I am trying to develop a first eval / test program for the BMD-340-EVAL evaluation board using Keil. However, I don't seem to be able to download the required Keil pack. Other...
Hi,
I want to send multiple packets on a notify characteristic using ble_blanky app as baseline but only first 4 consecutive notifications are received on android side....
I would like to set the UUID below, so please tell me how to set it. 1)base UUID: 2)Service UUID： 3)Status Characteristics UUID： 4)Control Characteristics UUID： 5)Blood...
Hi,
I am using
nRF52840
SDK 15.3.0
Keil IDE
The soft device is S140
JLinkRTTViewer for debug
I set tx power in advertising as below.
sd_ble_gap_tx_power_set...
Hi,
We are developing a product that consists of a "central" and "peripheral" device. A small amount of data is periodically send from the central to peripheral device...
Hi. We are using nRF52832 and we have problem with UARTE. SoftDevice version - S132 5.0.0, SDK version - 14.2.0. Our application uses nRF and Mbed Serial to communicate with...
I have created my own custom project based on the template ble app, porting over the relevant includes and settings in order to start fresh. Despite my section placement file...
Hello,
I'm using a development board PCA10040 with sdk 16.0 I'm trying to organize a data streaming between two devices. Nrf52 board collect data (27 bytes with interval...
I bought dev board for evaluation purpose (currently run on ESP32)
chip: nrf52832 board: E104-BT5032A-TB ( http://www.ebyte.com/en/product-view-news.aspx?id=956) framework...
Hello Nordic! Im making a custom Nrf5232 QFAA, and for the antenna, I want to use only a grounded micro-coax connector and not a trace antenna, is this even possible? I've...
1. I want to use the following command line to compile the nrf9160 project, but the error.
2. Can you help me find the cause of this error?
3. Please provide me with...
Hello, I encounter a problem when I am trying to measure the current consumption of the nRF52840 on the nRF52840-DK. I have set the board in direct supply mode as described...
