Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hello,
I would like to switch on a led of a nrf52840 dongle by pressing the buton of another dongle. I don't know which example to use from SDK 17.0.2 to make a master/slave...
Pairing is rejected after setting,
i)APP_ADV_DURATION to 0
ii)adv. flag in adv. init from BLE_GAP_ADV_FLAGS_LE_ONLY_LIMITED_DISC_MODE to BLE_GAP_ADV_FLAGS_LE_ONLY_GENERAL_DISC_MODE...
Hi,
I tried to implement the UART in my code, based on the UART example code. Just as in the example, I first define the struct with the pin numbers:
The pins in this...
I found there was a example in "nRF5_SDK_15.2.0_9412b96\examples\dfu\secure_bootloader\pca10056_uart\arm5_no_packs" .
Is there a applicaion example that when it recv a specific...
Hi
I need to connect to perticular central and i know the central MAC address. So i am using whitelisting in peripheral.
I made below changes in my code in ble_app_uart...
I am trying to use the gzp_dynamic_pairing example in SDK version 16 with Segger Embedded Studio and the PCA10040 dev board. There is no project for SES so I copied what I...
Hi,
I am working on nRF5_SDK_17.0.0_9d13099\examples\peripheral\uart project.
How can I increase the UART buffer? like if I have to receive 100+ bytes data how can I read...
I am using a nRF9160 DK. I'm using a Windows 10 system and setup the SDK using nRF Connect.
I've started to experiment with the serial_lte_modem project -- version 1.3.1...
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fug_nrfutil%2FUG%2Fnrfutil%2Fnrfutil_intro.html links to two pages which cannot be found: https://infocenter.nordicsemi...
Hi,
I am able to transfer data from my custom peripheral device with nRF52840, but data is moving much slower than it should.
I am writing 244 bytes into NUS within...
Hi,
I am trying to use Cbor library provided the SDK version 1.3.0, I have added the module in my prj.conf file, however the documentation (at the top of cborencoder.c)...
This is the name that is advertised when the device is in DFU bootloader mode.
I've copied the bootloader_secure_ble from /examples/dfu/ but I cannot find where to change...
Hi every body,
My system was able to wake up on gpio on dev kit but after adjusting pin , my custom board is not able to wake up.
I'm in debug mode, it was also working...
Hello,
I am trying to send a single adv packet when a certain condition in the application is met. To do this I am calling ADV_start for the initial adv packet and then...
