Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hello.
I have found this document and have a question.
In according with document below: service " Generic Access" (UUID1800) has a few characteristics: " Device Name...
We're attempting to get a Bluetooth data stream set up on our nRF52840. We've taken Zephyr's peripheral sample and pared it down somewhat to only allow indications from the...
Hello,
I am working on LPN node code from the mesh SDK 3.2.0. When I run the example code, I see a current peak at every 2 sec interval. Please check the image attached...
Hello,
I managed to flash the AT command client to the board and connect to a network (both verified by COPS and CEREG)
Am I right that there is currently no AT command...
Hello,
We start using of our BLE devices with more or less permanent connection with our central BLE device, it was needed for Alisa connection.
BLE peripherals are old...
Hi,
I am a beginner in nRF52840. I want to add a channel hopping feature in the 802.15.4 example .
As per my understanding of source code, we can set the channel number...
I am looking for a way only a known/trusted device can connect and write/read information from my device. Filtering by address(white-listing) is not feasible. So what is a...
Device:
Peripheral only
Peer Manager and Bonding working
S140 radio
nRF5 SDK 15.2.0
Rigado BMD-340 module
Central == iOS devices
Our nRF5 module is controlled...
Hi, I'm on last step of developing, but I have this critical trouble. For the project, I started from ble_app_buttonless_dfu sample of SDK15.3. I added some peripheral (one...
I'm using the ble_app_grs_freertos example. I'm trying to maximize its thru-put potential for Central devices which can support the high data rates. For this I've used the...
Hi, guys,
What I do:
Add freeRTOS into ble_app_hrs example project in SDK15.0
What matter I get:
When I set NRF_SDH_BLE_GATT_MAX_MTU_SIZE as 247, the device can not...
Hi Guys,
I am using Si7021 I2C temperature sensor and I want to read the temperature value using nrf52840-DK. I connected the sensor to the 27,26 pin.
I wanted to read...
DK version: nRF5_SDK_15.0.0_a53641a
Softdevice version: s132_nrf52_6.0.0_softdevice
I am using a Fanstel BT832X SOC, which has the SKY66112 PA, on a custom PCB. The...
