What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi
I have a question about using gazell link layer and paring library with concurrent timeslot api. I try to do this but i have the hard fault handler after invoked nrf_gzll_init...
HI,
I want to use PWM to control various hardware (LED's, etc ..) so I started off from the suggested PWM code example, found in this forum + modified it as I want to use...
Hi.
I work with PCA10040 and SKD_14.2.
I use UARTE with easy DMA. I see big enough delay between sending nrf_drv_uart_rx_abort and entering to UART event hanler. What...
I tried to create a descriptor for a characteristic. I modified the app_blinky and added a ble_add_descr_params_t variable. After The Initialisation and definition of the...
Hi,
I've tried blink,hid,uart,template similar sdk examples so far. Now i acquired some experience about nrf52832 processor and bluetooth,but ii don't really have enough...
I have had an issue recently with some beacons that I am using to log temperature data. A portion of the beacons drained their batteries very quickly and didn't respond to...
Hi I have this piece of code which works in SDK 12 but when I port it to SDK 15 the sd_ble_gatts_characteristic_add function would fail with an error code of 7. No change...
Hi,
I want to put my nrf52832 into the low-power mode. I select SYSTEM ON with low-power (instead of SYSTEM OFF) in order to overcome reset. In order to do it I call sd_app_evt_wait...
Dear nordic team
I am using SEGGER EMBEDDED STUDIO and nrf52840 DK. I want to add some pwm nrf_drivers like nrf_nvic.c , nrf_soc.c , nrfx_pwm.c to my project. when i added...
Hello,
I started off with two nRF52832 Dev Kits, and have customized the UART Central - Peripheral example to send an array data from Peripheral to Central (no uart simulation...
A month ago I bought an nRF52840 DK to start creating my own projects with the nRF52840 chip
I have created a new project in Segger Embedded Studio for the nRF52840 DK....
Hi,
is it possible to use the nRF52 dev kit and/or the nRF52 Dongle (nRF52840 Dongle) wiith the dongle firmware without nRFConnect?
Background:
We want to use a nRF52...
AIM: Try ATT MTU Throughput Example on nRF52810 running on S132 v5.1.0
Reason: Cant use S112 on nRF52810 because of data length extension. Max speed achievable is 330 Kbps...
Hi,
I have nRF52832 connected to a device(A) which can operate from 3.3V to 5V supply.
When the device's supply is 3.3V, it communicates with nRF52832.
Before the device...
Hi ,
If the softdevice had inited (called sd_ble_enable() ) , Can I use the NVIC_EnableIRQ (or NVIC_DisableIRQ )
to enable/disable an interrupt ?
What is the difference...
Hi,
I would to know if it is possible to have an interrupt handler on a coming BLE Connection event?
What could be the jitter on this event?
Thanks,
Regards,
Se...
