Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi, I am going to use the nRF91 DK to program an external PCB with the nRF9160 on it. The DK documentation says that only 1.8V or 3.0V is supported for external debug/programming...
I am running on a Windows 10 PC.
I've downloaded and installed all the tools for the nRF9160 DK using nRF Connect.
After installing the Segger Embedded Studio, I followed...
Parts of this discussion started on this thread: i-am-trying-to-do-dmx512-protocol
I am using SDK 15.2.0 on an nRF52810. My test board is based off of a Laird BL651 which...
I am trying to setup SEGGER Embedded Studio to program the nRF52840 dongle hardware. I followed the Getting Started Assistant program to set up the development software for...
The SDK version I am using is V15.0.0.
I use the function interface nrf_gzll_set_pa_lna_cfg 。 The following is my configuration information：
static nrf_gzll_pa_lna_cfg_t...
Hi dear community,
I am currently using nRF52 DK which has 52832 on it. I am using it for my bachelor thesis project and want to create simple sensor network. I am using...
Dear,
I am using nRF9160 DK,
firmware: secure_boot & AT_client
and Tale_SIM from Telia, I want to get the current GPS position by AT command?
Is it possible? Which...
Hi,
In a design which should be compatible with the NRF52832 we want to use the NRF52840. As the NRF52832 doesn't have USB, this would mean that the VBUS and data lines...
I am confused because i see documents referring to cmake/ninja and west. Recently it looks like people are suggesting to use west with master branches. Can someone definitively...
Hi all
nrf52840 Development board,sdk is nRF5_SDK_15.2.0_9412b96 ,PC is windows 10 .My testing master device is cell phone(Huawei HTC and so on,android system),and using...
Hi
nrF52840 SoftDevice S140 - What is the max ATT_MTU size supported? 244 bytes?
Is there any allowed number of packets per connection event that can be transferred on...
Hey, I just got this nrf52 board with pca10040 and tested few Nordic's examples, which worked just fine. I want to simply put some sine wave signal to one analog input and...
Hello all,
I'm working on a device using nRF52832, interfacing to another microcontroller. I was seeing higher than expected consumption, so started to reduce code to find...
Hi
I just downloaded the nRF connect v2.6.0 - Programmer, but i don't what i have to do to start writing the code.
I only get 2 ``Boxes``, and one of them is called File...
