Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi guys,
I've almost got DFU working on SDK10. However I am having issues at post validation of the image, specifically in the function dfu_init_postvalidate() in file...
Hello all,
Thank you in advance for taking your time for reading this question. I'm developing a proximity application and I have programmed the nRF51 DK with the s110...
Hi,
I am trying to set up a small mesh network. Basically I have a couple of PCA10028 (v1.1.0) and I have flashed the mesh example:
github.com/.../BLE_Gateway
One...
Hello Everyone,
I have been working around BLE profiles for few months and i have made several tested for each service via MCP(android) everything works fine but now i...
Mt need is to do frequency measurement of 0.01Hz to 99.99 Hz
We need a clock of 1us that added to a timer of that start on when the pulse low to high event happens and...
Hi there,
I want to connect multiple nus devices to S120 central. After connection with device, it starts to scan again after the BLE_GAP_EVT_CONNECTED event. And there...
Hi,
I am using the s110 and SDK 6 and trying to have multiple notifications from different services/caracteristics. For now I have two services, one for the battery and one...
Hello, i have a strange situation here with TWI module and i have no idea what is happening. I have read a lot of posts here on devzone and the code i am using is also found...
Hi,
I am using nRF51822 spi as a master to communicate with the AFE. Four bytes need to transfer each read or write process. I use nRF51_SDK_10.0.0_dc26b5e.
Configuration...
hi
I am trying to gather information on what is needed to create a mesh network using BLE.
I am more familiar with Zigbee/Thread, but I am asked to implement something...
I downloaded S212 for nRF52 from thisisant.com and programmed the softdevice to nRF52832DK(PCA10040) via nRFgo Studio. Then I copied the 'include' folder of unzipped softdevice...
I have been trying nrf-sniffer with no success. Setup is:
Win7 64,
Sniffer Win 1.0.1,
Wireshark 1.10.14 (both win32 and 64 tried),
PCA10000 and PCA10001
The sniffer...
I generally upload codes from mbed.org to my PC then send the hex file to nRF51822 by nRF51-DK's pins. But I don't want to use cables to upload hex codes to nRF51822. Are...
Hi community,
When I want to use the example multilink peripheral inside the s120 directory example of the SDK 6.1.0, I'm not able to compile the code.
The device_manager_peripheral...
