Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Hi everybody
I make an application which combine ANCS and NUS services on my device (nrf51 SDK 9.0.0,softdevice 8.0) This application works properly when I use IOS device...
Could you explain why 8 reload registers exists. Its use and use case. Since I believe we need to reload every register each time we have to reset counter.
I have a rare issue where my device won't advertising as it is waiting for a Pending Flash event to clear. However I want to add a supervisor time-out to this. It is safe...
Hi ,
I am getting error in pstorage_store function .
On further digging function
if ((!is_word_aligned(p_src))) is returning the error.
What does this function check...
I use nrf51822qfaa,s110 v8.00,keil MDK IDE. If the program is wrong,The chip will reset, I want to save some data to the FLASH area before the chip reset. What I need to do...
The example DFU project (dual_bank_ble_s110) for NRF51422 seems to work just fine on my custom board that has NRF51822. Is there a problem to use it like that if I set the...
Dear community,
I'd like to report a problem on the Direct Test Mode software provided in nrf51 SDK v6.1.0.
In this mode, 2-bytes commands are transmitted over the serial...
Whenever I try to run the following Convolution function for the 12th time in my code, the Processor is halted and I get the following Error on console:
Performing single...
According to this example, the device should be advertising RX and TX Characteristics. I also believe that when I connect to the UART app using my iphone, I should be able...
I have been successfully using my nRF52 Dev Kit (PCA10040) for the last few days. Today, when messing around with the UART drivers, I seem to have messed up the JLink-OB....
Hello,
I have an NRF51822 beacon board and two small 0.96" OLED displays (does not matter for me which one o use). One with GND, VDD, D0, D1, REST, D/C, CS and VCC pins...
I'm on windows 8 using the 1.0.1 sniffer application and wire shark 1.10.14 64bit with a Nordic nrf51 dongle. I'm using an nrf51 dev board with ble_peripherals/ble_app_blinky...
with nrf51 there is 2 blocks (block0 for softdevcie and block1 for user data and stack). I configured the system to retain RAM before going down using sd_power_ramon_set(0x00030003...
Hi,
I have a device that is configured to work in GAP central role. This device only scans for specific advertisements from specific devices. Could you suggest how I can...
Hi!
I used the develop board test the application "ble_app_multilink_central" and "ble_app_multilink_peripheral",but it is always connected failed,and disconnect Reason 0x0008...