Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi.
I have following error:
Here is my prj.conf :
I would like to avoid using CONFIG_SHARED_INTERRUPTS.
Only GPIOTE0 is on IRQ number 11 so I couldn...
Hello,
I build the ZBOSS NCP sample from NCS v2.6.0 for the nRF52840 dongle. I use the optimization flag -O2 (for speed) in the build configuration (VS Code NCS extension...
Hi,
I am working with the Matter Light Bulb sample . I have come across a problem where I can not compile my firmware if I implement the occupancy sensor cluster using the...
Hello,
I am uploading my code with a basic URI to be advertised by the chip.
I am able to build and upload the code for the nrf52832 in my nrf52 DK, the program works...
Hello Team,
I am using nrf52840 board which supports ZIGBEE . Setup Details: Zigbee_LIGHT_BULB (nRF52840 DK) Zigbee_LIGHT_SWITCH(nRF52840 DK)
Light Bulb Example
I am...
Hi,
Currently we are using nrf52832 for our IoT finger wearable gaming mouse. Is there any newer nordic ICs with low latency features suitable for gaming applications. ...
We are looking to use the nrF5340 as a Bluetooth Classic Bridge to Auracast Transmitter.
There are some products on the market that allow you to make a standard bluetooth...
Dear
We are using the SDK15.2.0, we found after the DFU, the device reset and the consumption is normal first, but after 70+ seconds, the current consumption become abnormal...
HI all!
I've been doing some research on working with nRF Cloud and I have a few questions/clarifications:
1. In general are you able to drive/control a GPIO pin through...
I am trying to get provisioning by trusted user procedure of aws_iot working by making some changes in aws_iot nrf sample
I have tested it with permanent certificates and...
tl;dr
ZBOSS's version needs to be upgraded one by one. When migrating the SDK from 2.3.0 to 2.7.0 while preserving the persisted ZigBee network info, migrate the code to...
Hello,
Im developing a custom BLE mouse plus receiver, where they both implement the BAS BT service to keep track of the mouse battery.
So far I got it to work using my...
Hi,
I am having the same problem as nRF9160 UART: Loosing data when RxData is split into 2 buffers (Async API) - Nordic Q&A - Nordic DevZone - Nordic DevZone (nordicsemi...
Hi Nordic team
It was heard that Matter spec v1.3 will allow Matter WiFi device to be commissioned by WiFi directly, but not bluetooth.
Was this information correct? ...
