after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi,
I'm working with nRF5340 and would like to store my own data in the NVM (2 bytes in total).
I couldn't figure out which flash partition is relevant for this and what...
Hi,
There are two 'should' (as opposed to 'must') statements in the Fast Pair implementation guidelines for Locator Tags:
1. The Provider should reject normal Bluetooth...
Dear Nordic Support-Team,
I am trying to documentation on the Device Identity key in the nrf9160. I found something here: https://infocenter.nordicsemi.com/topic/ref_at_commands...
hello
I am studying DFU with reference to the Academy.
Exercise 1 - DFU over UART - Nordic Developer Academy (nordicsemi.com)
SampleCode of Exercise1 use McuBoot and...
Hello,
I want to use McuBoot so I added CONFIG_BOOTLOADER_MCUBOOT =y to prj.conf.
So t here were a lot of warnings "implicit declaration of function ".
Part of the warning...
Hi There,
Our peripheral firmware running nrf5 cannot seem to connect properly to our central running NCS 2.4.1 over BLE. We are consciously setting the connection to use...
Dear Nordic Support-Team,
the provided samples in nrf-SDK are great to show how to use several aspects of the nrf Sdk and the devices.
Nevertheless it would be great if...
I am planning to create an application on NCS that can have https://github.com/nrfconnect/sdk-nrf/tree/main/samples/bootloader using CONFIG_SECURE_BOOT=y, But is it possible...
TLDR; Need advice on which wireless communication protocol to use for five nRF52840 dongles within 75 feet of each other. I've never worked with Nordic Semiconductor products...
I'm experiencing an issue with I2C communication between the SEN5X sensor and multiple nRF9160 DK boards. The problem manifests as an crc error during I2C read operations...
In case I run the code from zephyr/samples/bluetooth/broadcast_audio_source, I get following error, when I play audio:
After I stop the audio, the log messages stop...
Hi,
I'm pretty new to Zephyr and I have to figure out how to connect to a NOR flash over SPI. Final application is the implementation of a file system, e.g. littlefs.
...
Hello !
I recently updated our project SDK from 2.6.0 to 2.7.0 and our custom board to HW v2 layout. Everything went almost seemless until I tried to enable sysbuild option...
We created a product using nrf52840. the product is operating well, but it has been confirmed that software reset (0x04) operates in very few times (2weeks per 1time). In...
